Journal of energy technology

številka: 1 (2014)
številka: 2 (2014)
številka: 3 (2014)
številka: 4 (2014)
Project Achieve - reducing energy consumption in fuel-poor households (iss. 1, 2014)
Potential of the Research Energy Centre to enhance energy specialisations in the Savinja-Šalek region (iss. 1, 2014)
Dogajanja v svetu in njihov vpliv na energetiko v Evropi in pri nas (iss. 1, 2014)
Development of the computer programs CORD and DMR in ZEL-EN PE GEN Energija - a status review (iss. 1, 2014)
Overview of research studies on underground coal gasification in Slovenia (iss. 1, 2014)
Analysis of voltage sag propagation through the distribution network (iss. 1, 2014)
Renewable energy potential and opportunities for organic farming in the region of the Šalek valley (iss. 2, 2014)
A case study of exergy analysis of waste heat recovery in refrigeration system (iss. 2, 2014)
Global trends and the thermal energy capacities greater than 10 MW in Slovenia (iss. 2, 2014)
Current-temperature analysis of the ampacity of overhead conductors depending on applied standards (iss. 2, 2014)
Odkupne cene električne energije, proizvedene iz OVE virov in SPTE v Sloveniji v letu 2014 (iss. 2, 2014)
Small hydropower plants in Slovenia (iss. 2, 2014)
Review of energy regulations on solar energy (PV) in Slovenia and Austria (iss. 3, 2014)
Low enthalpy systems in geothermal energy (iss. 3, 2014)
Formula for calculation of magnetic field strength over the middle of the gap of a bipolar suspended iron separator (iss. 3, 2014)
Cena nafte na svetovnem trgu vse nižja in nižja (iss. 3, 2014)
Numerical analysis of lift and pressure coefficients of an airfoil (iss. 3, 2014)
Turbine sealing steam heat recovery with dynamic Stirling engines (iss. 3, 2014)
Ali je že napočil čas za nov korak v energetiki? (iss. 4, 2014)
Large hydro power plants in Slovenia (iss. 4, 2014)
The optimization options of water supply systems in terms of energy consumption (iss. 4, 2014)
A spatial evaluation of the impact of air pollution (iss. 4, 2014)
Numerical analysis of an axial flow fan (iss. 4, 2014)
Stability assessment in a power system control centre (iss. 4, 2014)

številka: 1 (2015)
številka: 2 (2015)
številka: 3 (2015)
številka: 4 (2015)
Numerical analysis of a heat exchanger (iss. 1, 2015)
System control in conditions of fuzzy dynamic processes (iss. 1, 2015)
Cogeneration and trigeneration systems (iss. 1, 2015)
An overview of the exploitation of steam in the secondary systems of NPP Krško (iss. 1, 2015)
Business models for energy performance contracting (iss. 1, 2015)
Numerical and experimental investigations of transient cavitating pipe flow (iss. 2, 2015)
Determination of the conditions for the existence of higher-order differential electromagnetic invariants (iss. 2, 2015)
Electric cars in Slovenia (iss. 2, 2015)
Integer programming and Gröbner bases (iss. 2, 2015)
The exploitation of ultra-low-enthalpy geothermal energy in an ORC process in combination with RES and a heat pump (iss. 3, 2015)
Hydraulic transient control of refurbished Francis turbine hydropower schemes in Slovenia (iss. 3, 2015)
Three-phaze fuzzy model of a dynamic production system (iss. 3, 2015)
Wind energy in Slovenia and Austria (iss. 3, 2015)
Determination of local brittle zones at the crack front in the HAZ of welded joint (iss. 4, 2015)
Design of the ventilation and air-conditioning system in an office building (iss. 4, 2015)
On the isochronicity of periodic solutions at a centre manifold (iss. 4, 2015)
The application of nanomechanics in energy technologies (iss. 4, 2015)
The inverted distorted parabola-like shape of the bias-dependent electric field at an electron-injecting metal/organic interface deduced using the current-voltage method (vol. 8, 2015)

številka: 1 (2016)
številka: 2 (2016)
številka: 3 (2016)
številka: 4 (2016)
Simulation of commissioning in warehouse (iss. 1, 2016)
Preparation of National programme for spent fuel and radioactive waste management taking into account the possible future evolution of ERDO (European Repository Development Organisation) (iss. 1, 2016)
Response of the Krško nuclear power plant cointainment to the loss of coolant accident in computer code APROS 6 (iss. 1, 2016)
Design of a train articulation system (iss. 1, 2016)
Underground coal gasification (iss. 2, 2016)
Cable-aging management program implementation in nuclear power plants (iss. 2, 2016)
Differential equations, difference equations and fuzzy logic in control of dynamic systems (iss. 2, 2016)
Fracture properties of titanium bone implants corroded by simulated body fluid (iss. 2, 2016)
Smart grid design for efficient building management (iss. 2, 2016)
An overview of regulations regarding photovoltaic systems in Slovenia (iss. 3, 2016)
Elemental analysis of welds with an X-ray fluorescence analyser (iss. 3, 2016)
Sustainable energy planning in Slovenian municipalities (iss. 3, 2016)
Energy renovation of the Letuš Cultural Centre (iss. 3, 2016)
Ultrasonic detection of defects in steel welds (iss. 3, 2016)
Analysis of the opposite reactive power direction phenomenon on two parallel overhead transmission lines (iss. 4, 2016)
Device for the manufacturing of ovens by resistance seam welding (iss. 4, 2016)
The application of fuzzy linear programming methods in energy planning (iss. 4, 2016)
Cleaning of flue gases in thermal power plants (iss. 4, 2016)
Principles of water hammer interferometer (iss. 4, 2016)
Analysis of the Krško NPP spent fuel storage criticality safety under hypothetical degraded conditions (vol. 9, 2016)

številka: 1 (2017)
številka: 2 (2017)
številka: 3 (2017)
številka: 4 (2017)
Influence of shading on I-V characteristics of thin film PV modules (iss. 1, 2017)
Optimization of maintenance of gensets using expert systems for fault diagnosis (iss. 1, 2017)
Numerical analysis of an Ahmed body with different software packages (iss. 1, 2017)
Grounding system testing using a low-voltage U-I method (iss. 1, 2017)
Critical analysis of formulae for the calculation of the electrical parameters of humid material (iss. 1, 2017)
Determining the current capacity of transmission lines based on ambient conditions (iss. 2, 2017)
Dimensional accuracy of prototypes made with FDM technology (iss. 2, 2017)
The use of the Hook-Jeeves method for the calculation of complex nonlinear equivalent magnetic circuits (iss. 2, 2017)
Analytical estimation of switched reluctance motor flux linkage profile by using evolutionary algorithm and numerical simulations (iss. 2, 2017)
Efficient applications and architecture of modern digital signal processors (iss. 2, 2017)
On the centre-focus problem in some Liénard systems (iss. 3, 2017)
Research in the Laboratory of Thermomechanics, Applied Thermal Energy, and Nanotechnologies (iss. 3, 2017)
Analysis of outdoor LED lighting's dimming influence on the performance of LED drivers (iss. 3, 2017)
Influence of tail water level on the hydraulic performance of elbow draft tube (iss. 3, 2017)
The optimization of a race car intake system (iss. 3, 2017)
A straightforward analytical way of evaluating the single-phase inverter SPWM requency spectrum (iss. 4, 2017)
Hydraulic transient control of new and refurbished Kaplan turbine hydropower schemes in Slovenia (iss. 4, 2017)
The calculation of high-pressure viscosity for refrigerant mixtures (iss. 4, 2017)
Rotor mechanical stress analysis of a double-sided axial flux permanent magnet machine (iss. 4, 2017)
Future Generation IV SMR reactors (iss. 4, 2017)

številka: 1 (2018)
številka: 2 (2018)
številka: 3 (2018)
številka: 4 (2018)
Forecast of sustainable energy development in Slovenia (iss. 1, 2018)
Mechanical testing of heterogeneous energy components (iss. 1, 2018)
Root weld metal impact toughness of an energy component (iss. 1, 2018)
Research in virtual engineering (iss. 1, 2018)
Performance analysis of photovoltaic systems in the Brestanica thermal power plant (iss. 1, 2018)
Improving energy modeling and renovation through the monitoring of microclimate and indoor air quality (iss. 2, 2018)
History of classic thermodynamics and the future of thermodynamics (iss. 2, 2018)
Charging a car in motion wirelessly (iss. 2, 2018)
Experimental investigations of pipeline filling and emptying in a small-scale apparatus (iss. 2, 2018)
Energy aspects of urban last mile delivery (iss. 2, 2018)
Theoretical analysis of three parameters determining a thermal power calibration method for the TRIGA research reactor (iss. 3, 2018)
The efficiency of magnetic refrigeration and a comparison with compressor refrigeration systems (iss. 3, 2018)
Numerical optimization of brake discs for railway vehicles (iss. 3, 2018)
Visualization of electric energy production in Posavje in a mixed reality environment (iss. 3, 2018)
A magnesium-enhanced lime cleaning process of flue gases (iss. 3, 2018)
The PLC control of an electrical system consisting of an electromagnetically sliding brake and coupling (iss. 4, 2018)
Research activities of the Laboratory for Energy Management and Engineering (iss. 4, 2018)
Energy efficiency analysis in mobile hydraulics (iss. 4, 2018)
System control in a continuous stochastic input process (iss. 4, 2018)
Improvement of a Weedhopper 2 ultralight aircraft by using modern materials (iss. 4, 2018)

številka: 1 (2019)
številka: 2 (2019)
številka: 3 (2019)
številka: 4 (2019)
Thermal analysis and application of roll bond solar absorbers for heating and cooling in residential buildings (iss. 1, 2019)
Pantograph driven with a linear induction motor with adaptive fuzzy control (iss. 1, 2019)
Integration of Talum's roll-bond heat exchanger for different applications (iss. 1, 2019)
Analysis of pipeline vibration (iss. 1, 2019)
Energy indicators and topics in food supply chains' life cycle assessment (iss. 1, 2019)
Lift and drag coefficients for different magnus rotor types (iss. 2, 2019)
An analysis of the responsibility for zero waste (iss. 2, 2019)
Urban greening as a cooling tool towards the heat island effect (iss. 2, 2019)
PSpice simulations for single-phase rectifiers for testing DC fuses (iss. 2, 2019)
Influence of rotor structure on cogging torque in a surface-mounted PM-generator (iss. 3, 2019)
Electric and magnetic field measurements for high voltage transmission lines (iss. 3, 2019)
An alternative method of increasing the transmission performance of a conventional 110 kV cable line (iss. 3, 2019)
Challenges in the EMC standardization of wireless power transfer systems (iss. 3, 2019)
Response surface method-based optimization of outer rotor permanent magnet synchronous motor (iss. 3, 2019)
Assessment of the operating characteristics of brushless dc motors (iss. 4, 2019)
The external bias-dependent electric field at hole-injecting electrode/a-NPD junction and its relationship to Gaussian disordered interface states (iss. 4, 2019)
Power line magnetic field deviations for three different definitions of current unbalance (iss. 4, 2019)
Fracture toughness of HSLA welds made on penstock material (iss. 4, 2019)
A review of hybrid photovoltaic/ thermal systems (iss. 4, 2019)

številka: 1 (2020)
številka: 2 (2020)
številka: 3 (2020)
številka: 4 (2020)
Improving decentralized economic growth and reducing energy consumption in the European Union with the application of ecologically oriented innovations (iss. 1, 2020)
A simplified hybrid methodology for designing coreless axial flux machines (iss. 1, 2020)
Impacts of zero-emission powertrains based on hydrogen technologies in public transport (iss. 1, 2020)
The influence of delta ferrite on the quality assessment of austenitic stainless steel welds for the production of ovens (iss. 1, 2020)
Multi-purpose use and lifecycle analysis of solar panels (iss. 2, 2020)
A review of the use of Rankine cycle systems for hydrogen production (iss. 2, 2020)
The properties of the material gadolinium and the working agent used in the installation of magnetic refrigeration devices (iss. 2, 2020)
Reversible pump-turbines - a study of pumping mode off-design conditions (iss. 2, 2020)
Design influenced by the effect of filter selection on the appraiser variation of the measuring results of a 3D optical measuring system (iss. 3, 2020)
Innovative gasification technology for the circular economy (iss. 3, 2020)
A regenerator used in the installation of magnetic refrigeration devices (iss. 3, 2020)
Fuzzy model for estimating the risk of infection by Covid-19 (iss. 3, 2020)
Analysis of combustible fractions in mixed municipal waste and packaging and calculation of energy value (iss. 4, 2020)
Cost-benefit analysis of frost protection methods (iss. 4, 2020)
Analysis and efficiency of a gadolinium magnetocaloric material plate (iss. 4, 2020)
Production of artificial cold for industry, based on the magnetocaloric effect (iss. 4, 2020)

številka: 1 (2021)
številka: 2 (2021)
številka: 3 (2021)
številka: 4 (2021)
Limestone purity as the decisive factor for its consumption in the flue gas desulphurisation process (številka: 3, 2021)
Towards forty years of Krško NPP operation (iss. 1, 2021)
Modelling of magnetic regenerator and heat transfer agent in microchannels (iss. 1, 2021)
Comparison of cavitation models for the prediction of cavitation around a hydrofoil (iss. 1, 2021)
New technique to evaluate the overall heat loss coefficient for a flat plate solar collector (iss. 1, 2021)
Determination of produced and consumed electricity of a residential building using a graphical user interface (iss. 2, 2021)
A study of particulate and gase-ous emissions of a damaged tubu-lar combustion chamber in a pellet stove (iss. 2, 2021)
Static model of temperature distribution in a photovoltaic module (iss. 2, 2021)
3D coupled electromagneticthermal analysis of a hybrid electromagnetic system with magnetic flux modulation (iss. 2, 2021)
Geometry design and analysis of an electric bus for the interior ther-mal modelling (iss. 2, 2021)
Quality assessment of single-pass corner steel welded joints (iss. 3, 2021)
Comparative analysis of synchronous motors (iss. 3, 2021)
Measurements of the characteristics of an electric motor for an electric vehicle`s drive (iss. 3, 2021)
Transient circuit simulation of arc-free current breaking by resistance rise (iss. 3, 2021)
Experimental verification of the numerically determined parameters for the non-linear two-axis model of a synchronous motor with interior permanent magnets (iss. 4, 2021)
HRSG system description and water-steam analysis at the hrsg cold start-up (iss. 4, 2021)
Designing an electromechanical generator for energy harvesting (iss. 4, 2021)
Frost protection measures (iss. 4, 2021)
Methodology of immersive video application (iss. 4, 2021)

številka: 1 (2022)
številka: 2 (2022)
številka: 3 (2022)
številka: 4 (2022)
Measurement device for testing printed circuit board assemblies coming off the production line (številka: 3, 2022)
Hamiltonicity of certain cartesian products of graphs (iss. 1, 2022)
Reducing carbon footprint in an oem supply chain caused by inadequate interpretation of x-ray results of hidden defects in ductile iron castings (iss. 1, 2022)
Method of the best available technology and low carbon future of a combined heat and power plant (iss. 1, 2022)
The impact of unbalanced power supply on load currents in transient and steady-state operation (iss. 1, 2022)
Prediction of cavitation and particle erosion in a radial divergent test section (iss. 2, 2022)
Hydrogen production using a thermochemical cycle (iss. 2, 2022)
Overview of GNSS systems and their operation (iss. 2, 2022)
Analytical and numerical analysis of trapped air pocket dynamic response due to pressure change in liquid-filled pipelines (iss. 2, 2022)
Analysis of the influence of parameters when charging and discharging a capacitor using differential equations (iss. 2, 2022)
A company’s carbon footprint and sustainable development (iss. 3, 2022)
RFCS project methenergy+ methane recovery and harnessing for energy and chemical uses at coal mine sites (iss. 3, 2022)
The use of differential evolution to determine maximum generation and load values in the distribution network (iss. 3, 2022)
Use of active elements for providing suitable voltage profiles and prevent overloads in radial distribution networks (iss. 3, 2022)
Energo-economics payback investment calculation modelling of gas-steam combined cycle power plant (iss. 4, 2022)
Energy source replacement in a thermal power plant (iss. 4, 2022)
Energy analysis of hydrogen use in road transport of the Republic of Croatia (iss. 4, 2022)
Monitoring and assessment mechanism of just energy transition trajectories (iss. 4, 2022)

številka: 1 (2023)
številka: 2 (2023)
številka: 3 (2023)
številka: 4 (2023)
Generalised fuzzy linear programming (iss. 1, 2023)
Assessment of human exposure to electric and magnetic fields near transmission lines using FEMM (iss. 1, 2023)
Design of wFoil 18 Albatross with hydrogen technologies (iss. 1, 2023)
The impact of plug-in hybrid vehicles in low-voltage distribution systems using a Monte Carlo simulation (iss. 1, 2023)
Analysis of revitalisation model behaviour for thermal power plants in different geographical areas (iss. 1, 2023)
Optimal dispersed generation placement in radial distribution systems using a pattern of load flow procedure – clustering optimisation (iss. 2, 2023)
Using household flexibility as a part of demand-side management programs (iss. 2, 2023)
Seawater as a reagent in the flue gas desulphurisation process (iss. 2, 2023)
Visualisation of 4D thermal maps (iss. 2, 2023)
Optimization and analysis of an interior permanent magnet synchronous motor (iss. 3, 2023)
The influence of unbalanced current in bus bars on magnetic field distribution (iss. 3, 2023)
Validation of distributed energy resources in accordance with voltage fluctuation limitations prescribed by the IEEE 1547-2018 standard (iss. 3, 2023)
Robotic sanding of freestanding bathtubs (iss. 3, 2023)
An approximate model for determining the resistance of a hemispherical ground electrode placed at the top of a nonhomogeneous truncated cone (iss. 3, 2023)
Analytical estimation of the thermal stability of HTS magnets during sudden discharge (iss. 4, 2023)
Charging stations connected to street light power systems (iss. 4, 2023)
Inflationary elevated energy prices as the main factor of fuelling economically viable electricity production in EU fossil fuels based thermal power plants (iss. 4, 2023)
SWOT analysis of hydrogen economy (iss. 4, 2023)
Analytical estimation of the optimal PV panel tilt based on a clear-sky irradiance model (iss. 4, 2023)

številka: 1 (2024)
številka: 2 (2024)
številka: 3 (2024)
številka: 4 (2024)
Damage analysis of condenser cooling tubes in a thermal power plant (iss. 1, 2024)
Implications for the environmental-engineering compromise as a result of the aftermarket optimization of a diesel engine (iss. 1, 2024)
Methods for recycling photovoltaic modules and element recovery projections in Slovenia (iss. 1, 2024)
Conceptual techno-economic analysis of retrofitting a 210 MW thermal heavy-oil power plant with a molten salt thermal energy storage system for renewable power (iss. 1, 2024)
Analysis of aged cables` insulation with X-ray fluorescence spectrometry (iss. 1, 2024)
Configuration of a flat roof solar power plant for maximum electricity production (iss. 2, 2024)
Hardware in the loop testing of a protection monitoring and diagnostic system (iss. 2, 2024)
Analysis of the capacity of LiFePo sub 4 batteries based on the released electrons (iss. 2, 2024)
Conservation of fish migrations at hydroelectric power plants (iss. 2, 2024)
Heavy metal content in soils of selected hop plantations in relation to their natural background (iss. 3, 2024)
Addressing the challenges to the introduction of battery energy storage systems in renewable energy utilisation systems (iss. 3, 2024)
Heavy metal content in vegetable garden soils in relation to their natural background (iss. 3, 2024)
Verification and validation of student’s CFD tool on the venturi flow case (iss. 3, 2024)
Energy management in microprocessor-driven circuit design using sleep modes (iss. 3, 2024)
A review of artificial intelligence in nuclear power plants (iss. 4, 2024)
FFA FW flow influence at NPP Krško (iss. 4, 2024)
Assessing the effects of a hydropower plant basin on fish spawning in an upstream river tributary (iss. 4, 2024)
Theoretical and experimental investigations of a water hammer in Sava river Kaplan turbine hydropower plants (iss. 4, 2024)
Infrared thermography in the detection of water stress in plants (aug. 2024, 2024)