Acta Chim. Slov. 2005, 52, 53–59 53 Scientific Paper The Effect of Annealing on Structural, Optical and Electrical Properties of Nanostructured Tin Doped Indium Oxide Thin Films Mohammad Hossein Habibi* and Nasrin Talebian Department of Chemistry, University oflsfahan, Isfahan, 81746-73441, Iran Received 05-09-2004 Abstract A low level tin doped indium oxide, ITO, (ca. 10 w % Sn02) thin films were prepared on glass substrate by electron beam technique. Deposited films with deposition rate of 0.1-0.25 nm s1 were annealed at different temperatures from 250 to 550 °C in air. The thin films were characterized using low and high angle X-ray diffrac-tion and UV-visible spectroscopy. The lattice constant and the grain size of ITO thin film were 10.118 A and 36 nm, respectiveh/. UV-visible transmission spectra confirmed the formation of high quality ITO nano-particles. These low level tin doped indium oxide thin films showed higher transparency over the visible vvavelength region (ca. 95%) than those of already reported with higher level tin doped indium oxide thin films deposited at 350 °C. The transmission data were used for direct and indirect optical band gap calculations ca. 3.6 and 3.8eV, respec-tively. The refractive index and porosity of ITO films annealed at different temperature were calculated from measured transmittance data. The results showed that the refractive index of thin films increased with increasing annealing temperature, but the porosity of ITO thin films showed opposite trend. The lowest resistivity (2.9 X 10~6 il m) and highest porosity (40.1%) were obtained for the annealed film at 550 °C. Keywords: Nanostructure ITO, low and high angle XRD, UV-visible transmission spectra, annealing, electron beam evaporation. Introduction Metal oxide thin films like indium oxide and tin doped indium oxide have unique characteristics such as good conductivity, high optical transmittance over the visible wavelength region, excellent adhesion to substrates and chemical stability and photochemical properties. These properties are resulted from their n-type semiconductor behavior and wide band gaps. Therefore, indium oxide and tin doped indium oxide are used in a wide range of applications including šolar energv conversion and photovoltaic devices, flat panel displays and biocatalvtic redox transformation.13 New applications require ITO films with lower resistivity and higher optical transmissions over the visible wavelength region. In order to obtain optimal characteristic i.e. high transparency and low sheet resistance, the param-eters such as thickness of the film, dopant type and its amount and the other deposition conditions have to be optimized. Haacke defined a figure of merit quantity to specify the quality of transparent conductor.4 It is well known that the electrical and optical properties of semiconducting oxides like ln203 depend strongly on defect density created by external doping or disturbed stoichiometry as well as their preparation and growth conditions.5 Tin (Sn) is one of the suitable external dopants among the various doping elements such as F, Cl, Sb.6 When trying to get low resistivity ITO films, the amount of doping of tin (Sn) should be properh/ controlled. It is worth to note that the substitution of tin element within ln203 lattice is also important. If tin substitute with indium, it liberates a free electron into the lattice and the electrical conduction will increase but it also acts as a neutral impurity scattering center and decreases the electrical conduction when combined with interstitial oxygen atoms.7 In203 thin films have been deposited by a number of techniques such as de magnetron sputtering,8 RF sputtering,9 CVD,10 sol-gel,11 thermal evaporation,12 and spray pyrolysis.13 In spite of good potential of ITO thin films prepared by electron beam evaporation technique, less attention has been paid to the study of annealing temperature effect on its structural, electrical and optical properties. Further-more, the investigations on a number of nanocrystalline Habibi and Talebian Nanostructured Indium Oxide Films 54 Acta Chim. Slov. 2005, 52, 53–59 ITO thin films have demonstrated peculiar features of optical behavior of nanostructured films as compared with those of compact polycrystalline or single-crystal ones. These features are related both to the quantum-sized effect and the strong influence of the surface atoms, the number of which is comparable to those located in crystalline core. In the previous reports the dependence of the above mentioned properties were investigated on the substrate temperature,14 vapor pressure and the presence of ion beam irradiation,15 thickness of films,16deposition rate,17 tin doping level18 and deposi-tion parameters at ali19-20 and it has been less attention paid to the effect of annealing temperature for thin films deposited by electron beam evaporation. The aim of present work is to pay more attention to study of the annealing temperature influences on the structural characteristics, optical and electrical behaviors of low level tin doped indium oxide nanostructured thin films prepared by electron beam evaporation technique. Experimental Sample preparation An electron beam evaporation system similar to those shown in Figurel was used for film deposition. The evaporation conditions were: (1) a vacuum of 4.2 X 10~5 mbar; (2) an accelerating voltage of 1-10 kV; (3) electron beam current 10-12 mA and the rate of evaporation were controlled within the range 0.1-0.25 nm/s. The thickness of thin film was controlled by using a quartz crystal thickness monitor, resulting in films having 45 nm. The target material used in this study was an ITO pellet (purchased from Merck) with a composi-tion of ln203 89.75 wt%, Sn02: 9.82 and trace amount of other oxides which are determined by XRF analysis CaO: 0.12, K20: 0.096, Fe203: 0.069, CuO: 0.069, A1203: 0.025, ZnO: 0.025 and U02: 0.026. Glasses slides were immersed both in boiling sulfuric acid and Milli-Q water for 30 min and aftenvard they ultrasonically cleaned in acetone and absolute EtOH for 5 min. Finally they were rinsed with water. The substrate temperature during the deposition process was kept at 25 °C. The phase composition of ITO films annealed at different tem-peratures were characterized using XRD technique with a D8 Advanced Bruker X-ray diffractometer at room temperature, with monochromated CuKa (X =1.54 A) in the scan range of 26 betvveen 4° to 100° with a step size of 0.03 (26/s). Measurements were taken under beam-acceleration conditions of 40 kV/35 mA. The UV-visible optical transmission spectra of the thin films were recorded by a double-beam spectrophotometer Cary 500 scan. The sheet resistance of films was measured by four-probe method at room temperature. Figure 1. Electron beam evaporation set up used for thin films preparation; (a) Electron Beam, (b) Material Vapor, (c) Substrate, (d) Target Material, (e) Water Cooling Lines, (f) Shield, (g) Magnet, (h) To Vacuum Pump, (i) Tangstan Filamen. Results and discussion XRD measurements Tvpical low-angle XRD spectra of the tin doped ln203 thin films before and after heat treatment at ca. 550 °C were shown in Figures 2 and 3, respectiveh/. As it can be seen from Figure 2, before heat treatment ill-defined amorphous phase is appeared but after heat treatment, the well-defined structure of the multi layers is evident from the large number of peaks in the XRD pattern (Figure 3). Figure 4 shows the high angle XRD pattern for as-deposited thin film. It can be found that before heat treatment only one less significant shoulder appears in the 26 betvveen 20° and 30°. The low intensity of this feature suggests that this film consists of amorphous phase up to 450 °C. Figure 5 shows the variation of XRD patterns with annealing temperatures. The annealed film pattern at ca. 550 °C matches with ln203 reference peaks as body-centered cubic form which was observed as bar graphs in Figure 6. The figures clearly showed a change with annealing from a single broad amorphous peak centered 26 = 30° to a set of sharp, well-defined peaks positions expected the primitive cubic lattice crystal structure with a 10.118 A lattice parameter. In particular, the line at 26 =30.581° corresponds to the reflection from the (222) plane is close to the position of strongest line of the reference indium oxide. The other peaks were due to reflections from the (400), (431) and (440) planeš. None of the Habibi and Talebian Nanostructured Indium Oxide Films Acta Chim. Slov. 2005, 52, 53–59 55 Table1. Comparison between measurement XRD results and standard pattern for ln203 samples annealed at 550 °C for 24 h. Observed 29 (degree) Standard 29 (degree) h k 1 27.858 - 3 1 0 30.581 30.578 2 2 2 41.842 41.860 3 3 2 52.709 52.73 4 3 3 63.668 63.71 4 4 4 SO ] 40 -: 30-i 20 H | 11 i 11 i 11 11 i 11 i 11 i 11 | 11 i 11 i ii 11 i 11 i 11 i 11 11 i 11 | 11 i 11 11 i i^ 4 5 6 7 6 9 10 29 (°) Figure 2. Low angle-XRD pattern of tin doped ln203 sample before annealing. A\fw r\ 20 (°) Figure 3. Low angle XRD pattern of tin doped ln203 sample after annealing (550 °C). 2? (°) Figure 4. High angle-XRD pattern of tin doped In2O3 sample before annealing. 1800 --- J " ¦--------¦---------»-------*~ I I F ¦ M^ 1200 jrf4KL-. 1000 " ^ 1600 1400 ] 1200 1000 800 600 400 200 ->*1 ^Wta*wU__,„ **V>|» Bi,.i N (d) I Tii iiijiwiihKwmin.. 0>) ;W*r ^*w**«.miM,......ji*4kw^ *>"wi'ii»............. (a) 10 20 30 40 50 60 70 80 90 100 29 (°) Figure 5. High angle-XRD pattern of tin doped ln203 sample at different annealing temperatures: (a) as-deposited, b) 250, c) 350, d) 450, and e) 550 °C. lftlPTr^qTTn ™TIy" ti 20 30 4° 50 60 70 SO 90 100 29 (°) Figure 6. High angle-XRD pattern of tin doped ln203 sample after annealing at 550 °C. The bar graphs represents XRD pattern of ln203 sample. spectra indicated any characteristic peaks of Sn, SnO and/or Sn02, which means that the tin atoms were doped substitutionally into the ln203 lattice.6 In continuum, we also used the FWHM of line about 0.320 degree to calculate crystal size according to Debye-Scherrer formula21 which it was ca. 36 nm. A comparison betvveen measurement XRD results and standard pattern for ln203 were shown in Table 1. !___"" 2000 " 50 40 30- :." 10 " 5 6 10 Habibi and Talebian Nanostructured Indium Oxide Films 56 Acta Chim. Slov. 2005, 52, 53–59 Electrical property A sharp drop in resistivity was observed in the annealing temperature range betvveen 250 and 450 °C. The obtained lowest resistivity was 2.9 X 10^O.m at 450 °C, which could be attributed to improved crystalline nature of film during annealing. The more increase in temperature shows no further effect on resistivity (not shown here). The electrical property of the films was found to be related to the microstructure and crystal-lographic structure, which in turn strongly depend on the annealing temperature. Optical transmittance The transparency of thin films for aH temperatures exhibits a sharp decrease in about the UV region as shown in Figure 7. Transmission percent of ITO films was also changed from ca. 10 to 95% for as-deposited and annealed at 550 °C, respectively. The ripples in the spectrum resulted from the interference light, since they show wave forms that are characteristic of the Interference light.22 Further, there was a shift in adsorption edges to shorter wavelength with annealing temperature up to 550 °C which was due to the Burst-ien-Moss shift23 and/or it could also be related to the quantum-size effect.24 ¦iaa -i--------------------------------------------------------------------------------------------------------------------------1 aaa 4DD 5aa eoo 700 Figure 7. Optical transmission vs. wavelength of light for low tin doped ln203 thin film: (a) as-deposited, (b) annealed at 250, (c) 350 (d) 450, and (e) 550 °C. Refractive index and porosity The refractive index of prepared ITO films was calculated from the measured transmittance spectrum. The evaluation method used is based on the analysis of the transmittance spectrum of a weakly absorbing film deposited on a non-absorbing substrate.25 The refractive index n(\) over the spectral range is calculated by using the envelopes that are fitted to the measured ex-treme. See Equations 1 and 2, where n0 and ns are the refractive index of air and films respectiveh/, Tmax is the maximum envelope, and Tmin is the minimum envelope. The porosity of the ITO thin films was calculated us- ing the equation 3,26 where nd is pore-free ITO which is taken to be 1.8. It should be noted that the refractive index of ITO ranging from 1.8 to 2.1 in the UV-NIR region.2731 The calculated refractive index and porosity of ITO films are listed in table 2. The results showed that the refractive index was increased from 1.57 to 1.61 by increasing annealing temperature up to 450 °C and then was decreased by further increasing of annealing temperature which is due to crystallinity improvement. On the other hand, the porosity showed opposite trend and its maximum value (40.1%) was observed for ITO thin film annealed at 550 °C. n{X) = J S + J S2 - n2 (X)ns2 (X) (1) S = i(n20(^)+n2s(^))+2nons(r—(i)"r-(/l) ) (2) 2 Tmsx(X)xTmsx(X) Porositv = [1 - " ~ ] x 100(%) (3) n2d-\ a =/—!— (4) d Table 2. Refractive index and porositv of ITO films annealed at different temperatures. Annealing temperature (°C) Refractive index Porosity (%) 250 1.57 34.6 350 1.59 31.3 450 1.61 28.9 550 1.53 40.1 Estimation of ITO band-gap A given material can exhibit a direct or indirect band to band transitions depend on its crystal structure. For example, Si single crystals have an indirect transi-tion located at 1.1 eV. In contrast, the amorphous Si is characterized by a direct optical transition with a larger Eg value. In addition, both types of transitions can also be seen in the same material simultaneously, for example GaP. In order to distinguish betvveen direct and indirect transitions usually ušes adsorption depths which given by l/a. Ignoring the reflectivity, which is expected to be low, the absorption coefficient (a) can be determined from the film transmission, T, as shown in equation 4, where d is the thickness of the film in nm. The adsorption depth for direct transition span the 100-1000 nm range while in the indirect transition čase this quantity can be as large as 104 nm.32 With regard-ing this criterion, the adsorption depth versus incident photon energy plot was shown in Figure 8. It can be seen that the indirect transitions were most probable than the direct transitions. In order to obtain more insight Habibi and Talebian Nanostructured Indium Oxide Films Acta Chim. Slov. 2005, 52, 53–59 57 into origin of transitions, we used the other graphical method as follows. The direct and indirect allowed-forbidden band-gaps of the ITO films may roughh/ be estimated by plotting the (ahv)" versus hv (n = 2 for allowed direct, n =1/2 for allowed indirect, n =1/3 for forbidden indirect and n =2/3 for forbidden direct optical transitions) and extrapolating the linear region of the plot toward low energies.33 Figure 10 represents these plots for the ln203 electrodes heated at 550 °C. Extrapolating the linear parts of the (ahv)2 versus hv plots (Figure 9, n=2) gives a direct band gap (Egd) of 3.6 eV for the ITO film. Thus, the direct band gap estimated in the present work for the nanostructured ITO film is in a good agreement with the published values.34-35 hv (eV) Figure 8. The adsorption depth variation vs incident photon energy. A comparison of the allowed and forbidden transitions for ITO thin films which also was shown in Figure 9, indicates that the better linearization and the wider linear region are observed for the former transitions. This means that the indirect allowed transitions are realized in this film. The E^ value estimated in the present work was 3.87 eV at annealing temperature 550 °C. It should be noted that for ITO thin films, it is difficult to choose what type of indirect transitions is realized really. As it can be seen in Figure 9, in order to select the most probable band to band transition, the whole transitions have been overlaid. The allowed indirect transition is the most probable transition. The Burstien-Moss shift towards higher energies is clearly seen in band gap energy values of annealed ITO thin films shown in Table 3, which has also been reported by other authors.36 In order to compare the Haacke figure of merit quantity (cpTC = T10/Rs) of many techniques, the tansmit-tance and resistance results of ITO thin films prepared by various methods are presented in Table 4. The results showed that a relatively good figure of merit can be obtained by electron beam evaporation technique in comparison with the others. Electronic properties of tin doped ln203 (ITO) electrode in contact with 0.1 mol dnr3 H2S04 solution under visible light was investigated by means of linear sweep voltammetery and electrochemical impedance spectroscopy techniques.39 Figure 9. Comparison between allowed and forbidden direct and indirect transitions (eVcnf1 X 104)° in low level tin doped ln203 thin film heated at 550 °C for 24 h. Table 3. The variation of indirect band gap with annealing temperature. Annealing temperature (°C) Egi(eV) 250 350 450 550 3.71 3.78 3.80 3.87 Surface morphologv AFM image analysis was used to reveal the particle size and surface morphology of ITO thin films annealed at different temperatures. It was found that the films consisted of nanosize crystallite with a dimension of about 10^10 nm which is increased up to 550 °C. AFM image analysis also shows the depth of about 12-20 nm for annealed ITO films at different temperatures. The films contain obvious pore structures betvveen parti-cles, which are decreased during annealing at higher temperatures. Conclusions From the obtained results following conclusions can be drawn. 1) The XRD results showed that the crystallinity of ITO thin films was improved with annealing and nanocrystalline films with 36 nm in diameter grain size obtained at 550 °C. 2) High quality film with resistivity as low as 2.9 X 10~6O.m and a transmittance ca. 95% were obtained by electron beam evaporation technique. 0.10 0.08 0.06 0.04 0.02 3000 0.00 2500 hv eV 2000 1500 1000 500 4 Habibi and Talebian Nanostructured Indium Oxide Films 58 Acta Chim. Slov. 2005, 52, 53–59 Table 4. Comparison of ITO films characteristics prepared by different techniques. Technique p(Slm) Rs (SI n"1) Transmittance in the visible region (T%) Figure of merit (O. / n) Ref. Electron beam evaporation 2.9 x lO"6 Electron beam evaporation 3.0 x Kr6 Pulsed laser deposition 4.0 x lO"6 Magnetron sputtering 64 40 95 92 85 90 9.3553 x 10-3 8.7170 x 10-3 Presentwork [14] [37] [38] 3) The calculation of ITO thin films refractive index showed that the porosity was also improved by annealing. 4) The allowed-indirect transitions were the most probable transition and the allowed-indirect optical band gap was found to vary from 3.71 to 3.87 eV with increasing annealing temperature. 5) The Haacke figure of merit quantity comparison of many techniques showed that electron beam evaporation is a promising technique for preparing of nanostructure ITO thin films. 6) Electron beam deposited tin doped ln203 films annealed in air have a good potential for high conduc-tive and transparent window applications. 7) The surface of annealed film at different tem-peratures reveals that the films are homogeneous, but porous, which is suitable for photocatalvtic applications. The porosity improves the catalytic efficiency of the films due to increasing their effective surface area. The crystallite size was increased in the range of 10-40 nm during annealing. Acknowledgements We are grateful to Isfahan University Graduate School for financial support of this work. References 1. M. Wirtz J. Kluczik, M. Rivera,/. Am. Chem. Soc. 2000, 122, 1047-1056. 2. C. A. Martinez, J. D. Stevvart, Curr. Org. Chem. 2000, 4, 263-268. 3. C. G. Granquist, Appl. A: Solids Surf. 1993, 57, 19-22. 4. G. Haacke, /. Appl. Phys. 1976, 47, 4086-4089. 5. C. Liu, T. Matsutani, N. Yamamato, M. Kiuchi, Europhys. Lett. 2002, 59, 606-610. 6. J. L. Vossen,i?C4 Rev. 1671, 32, 289-291. 7. G. Frank, H. Kostim, Appl. Phys. A. Solids Surf. 1982, 27, 197-200. 8. I. A. Rvzhikov, A. A. Pukhov, A. S. Il'in, Microelectronic Eng. 2003, 69, 270-273. 9. E. Bertran, C. Corbella, M. Vives, Solid Statelonic 2003, 165, 139-148. 10. M. Penza, S. Cozzi, M. Tagliente, L. Mirenghi, C. Martucci, A. Ouirini, Thin Solid Films 1999, 349, 71-77. 11. S. K. Poznvak, A. I. Kulak, Electrochimica Acta 2000, 45, 1595-1605. 12. F. Zhu, C. Huan, K. Zhang, A. Wee, /. Appl. Phys. 1999, 86, 974-980. 13. K. S. Ramaiah, V. S. Raja, A. K. Bhatanagar, Semicond. Sci. Technol. 2000, 15, 676-683. 14. J. George, C. S. Menon, Surf. Coat. Technol. 2000, 132, 45^-8. 15. M. Yamagushi, A. Ide-ektessabi, H. Namura, N. Yasui, Thin Solid films 2004, 447-448, 115-118. 16. M. Bender, M. Seeling, C. Danbe, H. Frankenberger, B. Ocker, J. Stollenvverk, Thin Solid films 1998, 326, 61-11. 17. A. Salehi, Thin Solid films 1998, 324, 214-218. 18. K. Manivannan, A. Subrahmanvam,/. Appl. Phys. 1993, 26, 1516-1521. 19. I. Hamberg, C. G. Granquist, /. Appl. Phys., Lett. 1982, 40, 362-367. 20. C. Liu, T. Matsutani, N. Yamamoto, M. Kiuchi, Europhys. Lett. 2002, 59, 606-610. 21. B. D. Cullitv, Elements of X-Ray Diffraction, 2nd ed., Addison-Wesley, MA, 1978, p. 102-105. 22. H. Lin, S. Kumon, T. Yoko, H. Kozuka, Thin Solid films 1998, 315, 266-272. 23. E. Burstien, Phys. Rev. 1954, 93, 652-659. 24. A. V. Vorontsov, E. N. Savinov, J. Zhengsheng, /. Photochem. Photobiol. A: Chem. 1999, 125, 113-117. 25. J. C. Manifacier, J. Gasiot, J. P. Fillard,/. Phys. E9 1976, 1002-1004. 26. B. E. Yoldas, P. W. Partlovv, Thin Solid Films 1985, 129, 1-14. 27. M. Just, N. Maintzer, I. Blech, Thin Solid Films 1978, 48, L19-L20. 28. W. W. Molzen, /. Vac. Sci. Technol. 1975, 12, 99-105. 29. J. C. C. Fan, F. J. Bechuer,/. Electrochem. Soc. 1975, 112, 1718-1723. 30. Y. Ohhata, F. Shinoki, S. Yoshida, Thin Solid Films 1979, 59, 255-261. 31. K. Pommier, C. Gril, J. Marucchi, Thin Solid Films 1981, 77, 91-98. 32. Encvclopedia of Electrochemistrv, Edited by A. J. Bard and M. Stratmann, volume 6, “Semiconductor Electrodes and Photochemistrv" Willey VCH Verlag GmbH, 2002, p 25. Habibi and Talebian Nanostructured Indium Oxide Films Acta Chim. Slov. 2005, 52, 53–59 59 33. J. K. Pankove, “Optical Processes in Semiconductors”, 37. Dover Publications, 1971, Inc. Chapter 3, p 34. 34. M. J. Alam, D. C. Cameron, Thin Solid Films 2000, 38. 377–378, 455–459. 35. Seon-Soon Kim, Se-Young Choi, Chan-Gyung Park, 39. Hyeon-Woo Jin, Thin Solid Films 1999, 347, 155–160. 36. L. Meng, M. P. dos Santos, Thin solid Films 1998, 322, 56–62. Povzetek Komercialno uprašeno aktivno oglje je bilo uporabljeno za sorpcijo reaktivnega barvila Brillant Red HE-3B iz vodnih raztopin. Preučevan je bil vpliv pH raztopine, začetne koncentracije barvila, temperature in časa sorpcije na izčrpanje barvila. Ravnotežne sorpcijske izoterme so bile analizirane z linearnim, Freundlichovim in Langmuir-jevim modelom. Najvišji korelacijski koeficienti so bili dobljeni pri Langmuirjevih izotermah. Izračunani so bili navidezni termodinamični parametri. Iz njihovih vrednosti se lahko zaključi, da je sorpcija molekul reaktivnega barvila entropijsko voden endotermen proces. Kinetika sorpcije je bila analizirana z uporabo kinetičnih modelov psevdo-prvega in psevdo-drugega reda. Iz podatkov je razvidno, da je enačba drugega reda bolj primerna, kar nakazuje, da je difuzija v delce tista stopnja, ki določa hitrost sorpcije. H. Kim, C. G. Gilmore, A. Pique, J. S. Horwitz, /. Appl. Phys. 1999, 86, 6451-6461. J. F. Smith, A. J. Aronson, D. Chen, W. H. Class, Thin Solid Films 1980, 72, 469-474. A. Hassanzadeh, M. H. Habibi, A. Zeini-Isfahani,^4cto Chim. Slov. 2004, 51, 507-527. Habibi and Talebian Nanostructured Indium Oxide Films