H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM 705–710 OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM OKSIDACIJA JEKLA HT9 V VODNI PARI S TEMPERATURO MED 700 °C IN 900 °C Huayu Zhang 1 , Huiqin Chen 1* , Mengmeng Zhao 2 , Rui Tang 3 1 School of Materials Science and Engineering, Taiyuan University of Science and Technology, Taiyuan 030024, China 2 School of Materials Science, Northwestern Polytechnical University, Xi’an 710072, China 3 Science and Technology on Reactor Fuel and Materials Laboratory, Nuclear Power Institute of China, Chengdu 610213, China Prejem rokopisa – received: 2019-01-31; sprejem za objavo – accepted for publication: 2019-04-11 doi:10.17222/mit.2019.030 Oxidation behavior of the HT9 steel exposed to 700 °C –900 °C steam was investigated with gravimetry, X-ray diffraction and scanning electron microscopy. It was found that the oxidation kinetics of the HT9 steel followed the parabolic law. The mass gain increased with a decreasing temperature. The steam oxidation of the HT9 steel at 800 °C and 900 °C was selective. The ox- ides formed on the HT9-steel surface displayed a double-layer structure, consisting of an outer columnar Fe2O3 layer and an in- ner (Fe, Cr)3O4 layer. Keywords: HT9 steel, steam oxidation, oxidation mechanisms Avtorji so raziskovali oksidacijo jekla HT9 izpostavljenega vodni pari, ki je imela od 700 °C do 900 °C. Raziskavo so izvajali z gravimetrijo, rentgensko difrakcijo in vrsti~no elektronsko mikroskopijo. Ugotovili so, da kinetika oksidacije poteka v skladu s paraboli~nim zakonom. Prirastek na masi je nara{~al s padajo~o temperaturo. Oksidacija jekla HT9 pri 800 °C in 900 °C je bila selektivna. Oksidi nastali na povr{ini jekla HT9, imajo dvoplastno strukturo, sestavljeno iz zunanjega stebri~astega sloja Fe2O3 in notranjega (Fe, Cr)3O4 sloja. Klju~ne besede: jeklo HT9, oksidacija z vodno paro, mehanizmi oksidacije 1 INTRODUCTION With the depletion of traditional energy and the in- creasing environmental pollution, the nuclear energy plays a more important role to satisfy the urgent energy demand. 1 To guarantee the safety of a nuclear generator, fuel cladding materials are required to withstand the extreme working conditions, such as high temperature, high pres- sure, strong radiation and strong corrosion. 2–6 With the advantages of good resistance to a high radiation dose, high thermal conductivity, high creep-rupture strength, and excellent oxidation and corrosion resistance at high temperatures, the HT9 steel has a great potential for the application in the components of nuclear reactors. 4,7 In steam environments, about 9–12 % Cr ferritic steels exhibit an anomalous temperature dependence of the oxidation behavior. 8,9 Several studies indicate that multilayered oxide layers are formed on 9–12 % Cr fer- ritic/martensitic steels in steam atmospheres. Moreover, some defects, such as pores, voids and cracks, are pres- ent in the oxide layer. 9–13 The microstructures of the ox- ide and defects within the oxide layers depend on the ex- posure temperature and time. 8–10,14–17 Therefore, it is important to evaluate the oxidation behavior in the high-temperature steam for the nuclear fuel cladding ma- terials. 10,18 When the supply of a nuclear reactor coolant is insufficient, the temperature of the fuel cladding of nu- clear reactors rises rapidly. After severe loss-of-coolant accidents (LOCAs), a large temperature increase would lead to severe oxidation of the fuel cladding of nuclear reactors. 19 If the cladding tube cannot maintain its struc- tural integrity, the release of radio nuclides into the envi- ronment causes a catastrophic accident. In order to im- prove the safety and reliability of a nuclear reactor, it is necessary to evaluate the steam-oxidation resistance of the HT9 steel. In the present work, the steam-oxidation properties of the HT9 steel were investigated at (700, 800 and 900) °C. The weight gain and thickness of the oxide layers were utilized to characterize the oxidation properties. The morphology, chemical composition and microstruc- ture of the oxides were studied to reveal the oxidation mechanisms. 2 EXPERIMENTAL PART HT9-steel cladding is provided by the Nuclear Power Institute of China. The chemical composition of the HT9 steel is shown in Table 1. Figure 1 displays a TEM im- age of the HT9 steel, which consisted of tempered martensite and M 23 C 6 carbides. Carbides are precipitated Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710 705 UDK 669.148:66.040.2:66.094.3 ISSN 1580-2949 Original scientific article/Izvirni znanstveni ~lanek MTAEC9, 53(5)705(2019) *Corresponding author's e-mail: hyzhang76@tyust.edu.cn (H. Zhang), chenhuiqin@tyust.edu.cn (H. Chen) at the martensitic lath and prior austenite boundaries. The size of specimens was (10 × 10 × 0.6) mm. Prior to the oxidation experiment, the specimens were ground with SiC abrasive paper of up to 1200 grit, cleaned with ethanol and weighed using a balance (FA/JA*B) with an accuracy of 0.1 mg. The steam-oxidation experiments were performed in a tube furnace. Steam was produced by ebullition of deionized water and it flowed continu- ously into the furnace at atmospheric pressure. The wa- ter-vapor flow rate was 10 g/min. The test temperatures were (700, 800 and 900) °C, respectively. The specimens were tested at different exposure times of up to 100 h. The weight variations of the specimens were recorded at prescribed experiment intervals. The microstructure of the as-received HT9 steel was studied with a transmis- sion electron microscope (TEM, Tecnia F30). The cross-section of the specimens was ground and polished, and further observed with a scanning electron micro- scope (SEM, TESCAN MIRA3). The compositions of the oxide products were determined with an energy dis- persion X-ray spectroscope (EDX, Genesis XM) at- tached to SEM. The structures of the oxides were studied with an X-ray diffractometer (XRD, X’pert Pro). Table 1: Chemical composition of the HT9 steel (w/%) Element C Mn Si Cr Mo W V Ni N Fe Amount 0.2 0.69 0.32 11.4 1.02 0.48 0.28 0.54 0.45 bal. 3 RESULTS 3.1. Oxidation kinetics Figure 2 shows the variation of the weight gain of the HT9 steel with the oxidation time. It is found that the weight gain increased with the increasing exposure time and decreased as the temperature increases. In good agreement with the previous results, 8,17 this phenomenon suggests that the steel has improved its resistance to steam oxidation at high temperatures. Plots are also shown in Figure 1 and can be fitted with Equation (1): 3,6,10,16,18 Δmk t n = (1) where m is the weight gain per unit area in mg/cm 2 , k is the oxidation rate constant in mg/(cm 2 h n ), t is the time in h, and n is the time exponent. The oxidation kinetics of the HT9 steel at (700, 800 and 900) °C followed the parabolic law. It can be calcu- lated that the time exponents n are 0.33474 at 700 °C, 0.32948 at 800 °C and 0.13879 at 900 °C. The k values at (700, 800 and 900) °C are: 0.39564, 0.37599 and 0.21820, respectively. The highest k at the lowest tem- perature indicates that the HT9 steel displays the highest oxidation resistance at 900 °C. 3.2. Surface morphology Figure 3 shows SEM images of the oxides on the HT9 steel after 100 h in 800 °C and 900 °C steam. The oxidation of the HT9 steel in steam is not uniform. Many separate cellular oxides (Figure 3a) appear on the sur- face of the HT9 steel at 800 °C. The pox-like morphol- ogy means that the steam oxidation is selective rather than uniform. At 900 °C, cellular or flaky oxides can be found on the surface of oxidized steel. In addition, the grinding scratches can be observed, as shown in Fig- ure 3b. By comparing the morphologies of the oxides, it can be found that the oxidation was more serious at the lower temperature, in agreement with the results from Figure 2. Figure 4 displays surface morphologies of the HT9 steel oxidized at (700, 800 and 900) °C. It can be found that the spherical oxides develop a flocculent or nee- dle-like shape at 700 °C with the increasing exposure time, as shown in Figures 4a and 4b. At 800 °C and af- ter 50 h, the oxide particles become larger and a flake sub-structure can be observed, as shown in Figures 4c and 4d. The flake sub-structure further grows with the H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM 706 Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710 Figure 2: Weight gain of the HT9 steel as a function of exposure time at (700, 800 and 900) °C in steam Figure 1: TEM image of the as-received HT9 steel oxidation time. The evolutions of the morphology at 800 °C and 900 °C were similar. However, the oxide film had a cellular structure at 900 °C, and each cell was com- posed of many small crystal blocks, as shown in Figures 4e and 4f. Moreover, obvious cracks could be seen on the oxide film, as shown in Figure 4f. 3.3. Cross-sectional microstructure Figures 5a to 5f display cross-sectional microstruc- tures of the HT9 steel exposed to (700, 800 and 900) °C steam. 700 °C and 800 °C oxides are composed of two different layers, that is, a compact outer layer and a loose inner layer. Some cracks and voids are present in the ox- ide layers. The voids may coalesce into a crack after a long exposure time. 9,11 Crack propagation leads to an ex- foliation of the oxide layer. A breakdown of the oxide films can be seen in some regions. Both layers grow with the exposure time. Similarly, double oxide layers are also found at 800 °C and 900 °C. The outer oxide layer con- tains columnar grains perpendicular to the surface, shown in Figure 5c. Figures 5e and 5f show images of the cross-section of the HT9 steel at 900 °C. Localized corrosion products can be found. These phenomena indi- cate that a selective steam-oxidation behavior takes place at 900 °C, like in the previous studies. 17–20 Selective ox- ides also include two layers. The cracks between the outer/inner layers and inner layers/steel cause the exfoli- H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710 707 Figure 3: SEM images of the oxide films on the HT9 steel exposed to steam for 100 h: a) 800 °C, b) 900 °C Figure 5: Cross-sectional SEM images of the HT9 steel: a) 700 °C, 10 h, b) 700 °C, 100 h, c) 800 °C, 10 h, d) 800 °C, 100 h, e) 900 °C, 5 h and f) 900 °C, 100 h Figure 4: Surface morphologies of the oxidized HT9 steel: a) 700 °C, 50 h, b) 700 °C, 100 h, c) 800 °C, 50 h, d) 800 °C, 100 h, e) 900 °C, 50 h and f) 900 °C, 100 h ation phenomenon, as shown in Figure 5f. Sometimes, debonding of the outer layer makes it peel off from the inner layer. Figure 6 shows SEM images of cross-sections and elemental distribution of the oxide films on the HT9 steel exposed to steam. It shows that the outer layer contains Fe and O and the inner layers are rich in Fe and Cr. The O content is almost the same in the outer and inner oxide layer. The inner layer is determined as Fe-Cr spinel, in which the Cr content is higher than that in steel, and the Fe content is lower than in steel and the outer layer. To further confirm the composition of the oxides, six points in the cross-section were examined with EDS; they are listed in Table 2. The metal-to-oxygen ratio (M/O) for points 1, 2, 3, 4, 5 and 6 are 0.66, 0.77, 0.68, 0.76, 0.68 and 0.75, respectively. M/O in the outer layer is close to 0.67, consistent with that of Fe 2 O 3 . M/O in the inner layer is about 0.75 and consistent with (Fe, Cr) 3 O 4 . 3.4 XRD analysis Figure 7 shows XRD patterns of the outer-layer ox- ide film formed on the HT9 steel exposed to steam oxidi- zation for 100 h between 700 °C and 900 °C. Fe 2 O 3 and the HT9 matrix are present. The reasons for this may be the facts that the steam oxidation of the HT9 steel was selective and the outer oxide layer was so thick that the inner Fe-Cr spinel oxide could not be detected. The de- creasing intensity of Fe 2 O 3 with the increasing tempera- ture means that the amount of Fe 2 O 3 reduces at the higher temperature. In other words, the steam oxidation was more serious at the lower temperature and the outer layer was Fe 2 O 3 , indicating s superior resistance to steam oxidation of HT9 at the higher temperature. 4 DISCUSSION The above results indicate that the steam oxidation kinetics of the HT9 steel followed the parabolic law at the temperatures between 700 °C and 900 °C, suggesting that the oxide has a protective effect. Moreover, the steam oxidation of the HT9 steel was localized and a higher resistance to steam oxidation was observed at the higher temperature. A double-layer oxide, composed of the Fe 2 O 3 outer layer and (Fe, Cr) 3 O 4 inner layer, can be generated on the HT9 steel in 700–900 °C steam, which is similar to the results for the HT9 steel exposed to supercritical water. 14,16 As the oxygen affinity for Cr is higher than that for Fe, Cr is more likely to be oxidized to Cr 2 O 3 at the initial stage of oxidation. 10,14,21 The Cr content is not high enough to form a complete oxide layer; thus, discrete H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM 708 Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710 Figure 7: XRD patterns of the HT9 steel tested in a steam atmosphere for 100 h Figure 6: Cross-sectional SEM images and elemental distribution of the oxide layers on the HT9 steel exposed to steam: a) 700 °C, 100 h, b) 800 °C, 50 h and c) 900 °C, 50 h Table 2: EDS results corresponding to the points on the cross-section from Figure 6 (a/%). Element Point Fe Cr O M/O 1 39.58 — 60.42 0.66 2 30.97 12.40 56.63 0.77 3 40.63 — 59.37 0.68 4 24.24 18.80 56.96 0.76 5 40.52 — 59.48 0.68 6 30.82 12.11 57.06 0.75 Cr 2 O 3 forms at the metal/steam interface according to Equation (2), leading to a Cr depletion in the metal sub- strate. Therefore, the Cr content in the inner oxide layer is higher than that in the steel substrate, as shown in Fig- ure 6. The diffusion coefficient of Fe is higher than that of Cr in both oxide and metal matrix. Iron diffuses to the oxide/steam interface and reacts with H 2 O following Equation (3). It is known that iron oxide is more easily reduced by hydrogen than chromium. Fe 3 O 4 is reduced to Fe according to Equation (4). Then, Fe reacts with Cr 2 O 3 and steam through Equation (5). Fe 3 O 4 is oxidized to Fe 2 O 3 at the oxide/steam interface according to Equation (6). Therefore, a double-layer structure is formed on the HT9 steel. The process of oxidation is similar to that of the P92 steel in aerated supercritical water. The outer layer Fe 2 O 3 and inner layer (Fe, Cr) 3 O 4 grow at the ox- ide/steam and oxide/metal interface, respectively. The growth rates are controlled by the outward diffusion of Fe across the oxide layer. 2Cr+3H 2 O=Cr 2 O 3 +3H 2 (2) 3Fe+4H 2 O=Fe 3 O 4 +4H 2 (3) Fe 3 O 4 +4H 2 =3Fe+4H 2 O (4) Cr 2 O 3 +Fe+H 2 O = FeCr 2 O 4 +H 2 (5) 2Fe 3 O 4 +H 2 O = 3Fe 2 O 3 +H 2 (6) Exfoliation of the oxide layer depends on the stress state and relative strength of the oxide and oxide/metal interface. 11 Crack initiation and crack propagation result in two different types of spallation. The oxidation layer exfoliates due to non-penetrating longitudinal cracks in the oxidation layer, or it humps and bends until it breaks and exfoliates due to interface cracks between the steel matrix and the oxidation layer. 22,23 A thicker oxide layer indicates a higher possibility of exfoliation for the oxide layer. 11,24 Figure 8 shows the exfoliation of the oxide layers on the HT9 steel after exposure to steam. Some obvious ex- foliation can be observed in the local areas of the oxide scale. The exfoliation of the oxide scale from the HT9 steel was probably due to the growth stress taking place when the oxide formed and grew on the specimens and the thermal stress due to the temperature variation caused by the difference in the thermal expansion coeffi- cient between the oxides and the substrate. 25 If the oxide layer spalls at the interface between the inner and outer layers (Figures 8a to 8c), the oxidation rate of the HT9 steel and the thickening rate of the oxide layer after exfo- liation do not change substantially. The formation and growth of the oxide layer is still controlled by the diffu- sion of Fe and O through the inner layer. When the oxide layer exfoliates at the oxide/metal interface (Figure 8b), the oxidation rate of the steel becomes much higher than that before the oxide exfoliation. As can be seen in Fig- ure 8c, the outer Fe 2 O 3 layer was columnar. The oxide layer of the HT9 steel exposed to steam exfoliated by way of both non-penetrating longitudinal cracks and in- terface cracks penetrating the oxide scale. 5 CONCLUSIONS Steam oxidation behavior of the HT9 steel up to 100 h at 700–900 °C was investigated. The weight gain, phase constituents, morphologies and chemical composi- tions of oxide layers were investigated. It was found that the oxidation kinetics at (700, 800 and 900) °C followed the parabolic law and the mass gain increased with de- creasing exposure temperatures. Double-layer oxides were produced on the steel, consisting of outer layer Fe 2 O 3 and inner layer (Fe, Cr) 3 O 4 . Obvious cracks and exfoliation could be observed in the oxide scales. The formation and growth of the oxide layer can be explained with the diffusion of Fe and O. The oxide scales exfoli- ated due to non-penetrating longitudinal cracks and in- terface cracks penetrating the oxide scale. Acknowledgment This work was supported by National Natural Sci- ence Foundation of China, grant number 51575372 and the Fund for Shanxi Key Subject Construction. 6 REFERENCES 1 O. Anderoglu, T. S. Byun, M. Toloczko, S. A. Maloy, Mechanical performance of ferritic martensitic steels for high dose applications in advanced nuclear reactors, Metall. Mater. Trans. A, 44 (2013), 70–83, doi:10.1007/s11661-012-1565-y 2 C. Zheng, M. A. Auger, M. P. Moody, D. Kaoumi, Radiation induced segregation and precipitation behavior in self-ion irradiated ferrit- ic/martensitic HT9 steel, J. Nucl. Mater., 491 (2017), 162–176, doi:10.1016/j.jnucmat.2017.04.040 3 J. Bischoff, A. T. Motta, C. Eichfeld, R. J. Comstock, G. Cao, T. R. Allen, Corrosion of ferritic-martensitic steels in steam and supercriti- cal water, J. Nucl. Mater., 441 (2013), 604–611, doi:10.1016/ j.jnucmat.2012.09.037 H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710 709 Figure 8: Exfoliation of the oxide scale formed on the HT9 steel in a steam environment: a) to b) 700 °C, 100 h, c) 800 °C, 20 h and d) 900 °C, 20 h 4 Y. R. Chen, Irradiation effects of HT-9 martensitic steel, Nucl. Eng. Tech., 45 (2013), 311–322, doi:10.5516/NET.07.2013.706 5 L. Tan, M. T. Machut, K. Sridharan, T. R. Allen, Corrosion behavior of a ferritic/martensitic steel HCM12A exposed to harsh environ- ments, J. Nucl. Mater., 371 (2007), 161–170, doi:10.1016/j.jnucmat. 2007.05.001 6 L. Tan, X. Ren, T. R. Allen, Corrosion behavior of 9–12% Cr ferrit- ic–martensitic steels in supercritical water, Corros. Sci., 52 (2010), 1520–1528, doi:10.1016/j.corsci.2009.12.032 7 J. H. Baek, T. S. Byun, S. A. Maloy, M. B. Toloczko, Investigation of temperature dependence of fracture toughness in high-dose HT9 steel using small-specimen reuse technique, J. Nucl. Mater., 444 (2014), 206–213, doi:10.1016/j.jnucmat.2013.09.029 8 J. ¯urek, E. Wessel, L. Niewolak, F. Schmitz, T. U. Kern, L. Singheiser, W. J. Quadakkers, Anomalous temperature dependence of oxidation kinetics during steam oxidation of ferritic steels in the temperature range 550–650 °C, Corros. Sci., 46 (2004), 2301–2317, doi:10.1016/j.corsci.2004.01.010 9 P. J. Ennis, W. J. Quadakkers, Mechanisms of steam oxidation in high strength martensitic steels, Int. J. Pres. Ves. Pip., 84 (2007), 75–81, doi:10.1016/j.ijpvp.2006.09.007 10 X. Zhong, X. Wu, E. H. Han, Effects of exposure temperature and time on corrosion behavior of a ferritic–martensitic steel P92 in aer- ated supercritical water, Corros. Sci., 90 (2015), 511–521, doi:10.1016/j.corsci.2014.10.022 11 X. Zhong, X. Wu, E. H. Han, The characteristic of oxide scales on T91 tube after long-term service in an ultra-supercritical coal power plant, J. Supercrit. Fluid., 72 (2012), 68–77, doi:10.1016/ j.supflu.2012.08.015 12 N. Zhang, Z. Zhu, F. Lv, D. Jiang, H. Xu, Influence of exposure pres- sure on oxidation behavior of the ferritic–martensitic steel in steam and supercritical water, Oxid. Met., 86 (2016), 113–124, doi:10.1007/s11085-016-9624-1 13 Q. Shi, J. Liu, H. Luan, Z. Yang, W. Wang, W. Yan, Y. Shan, K. Yang, Oxidation behavior of ferritic/martensitic steels in stagnant liq- uid LBE saturated by oxygen at 600 °C, J. Nucl. Mater., 457 (2015), 135–141, doi:10.1016/j.jnucmat.2014.11.018 14 X. Ren, K. Sridharan, T. R. Allen, Corrosion of ferritic–martensitic steel HT9 in supercritical water, J. Nucl. Mater., 358 (2006), 227–234, doi:10.1016/j.jnucmat.2006.07.010 15 Y. Chen, K. Sridharan, S. Ukai, T. R. Allen, Oxidation of 9Cr oxide dispersion strengthened steel exposed in supercritical water, J. Nucl. Mater., 371 (2007), 118–128, doi:10.1016/j.jnucmat.2007.05.018 16 P. Ampornrat, G. S. Was, Oxidation of ferritic–martensitic alloys T91, HCM12A and HT-9 in supercritical water, J. Nucl. Mater., 371 (2007), 1–17, doi:10.1016/j.jnucmat.2007.05.023 17 V. Lepingle, G. Louis, D. Allué, B. Lefebvre, B. Vandenberghe, Steam oxidation resistance of new 12%Cr steels: Comparison with some other ferritic steels, Corros. Sci., 50 (2008), 1011–1019, doi:10.1016/j.corsci.2007.11.033 18 N. Q. Zhang, Z. L. Zhu, H. Xu, X. P. Mao, J. Li, Oxidation of ferritic and ferritic–martensitic steels in flowing and static supercritical wa- ter, Corros. Sci., 103 (2016), 124–131, doi:10.1016/j.corsci.2015. 10.017 19 T. Cheng, J. R. Keiser, M. P. Brady, K. A. Terrani, B. A. Pint, Oxida- tion of fuel cladding candidate materials in steam environments at high temperature and pressure, J. Nucl. Mater., 427 (2012), 396–400, doi:10.1016/j.jnucmat.2012.05.007 20 L. Martinell, F. Balbaud-Célérier, A. Terlain, S. Delpech, G. San- tarini, J. Favergeon, G. Moulin, M. Tabarant, G. Picard, Oxidation mechanism of a Fe–9Cr–1Mo steel by liquid Pb–Bi eutectic alloy (Part I), Corros. Sci., 50 (2008), 2523–2536, doi:10.1016/j.corsci. 2008.06.050 21 W. Gao, X. Guo, Z. Shen, L. Zhang, Corrosion behavior of oxide dis- persion strengthened ferritic steels in supercritical water, J. Nucl. Mater., 486 (2017), 1–10, doi:10.1016/j.jnucmat.2017.01.014 22 H. E. Evans, Stress effects in high temperature oxidation of metals, Metall. Rev., 40 (1995), 1–40, doi:10.1179/imr.1995.40.1.1 23 H. E. Evans, Cracking and spalling of protective oxide layers, Mat. Sci. Eng. A, 120 (1989), 139–146, doi:10.1016/0921-5093(89) 90731-4 24 E. Essuman, G. H. Meier, J. ¯urek, M. Hänsel, W. J. Quadakkers, The effect of water vapor on selective oxidation of Fe–Cr aloys, Oxid. Met., 69 (2008), 143–162, doi:10.1007/s11085-007-9090-x 25 N. H. Lee, S. Kim, B. H. Choe, K. B. Yoon, D. I. Kwon, Failure anal- ysis of a boiler tube in USC coal power plant, Eng. Fail. Anal., 16 (2009), 2031–2035, doi:10.1016/j.engfailanal.2008.12.006 H. ZHANG et al: OXIDATION BEHAVIOR OF HT9 STEEL IN 700 °C – 900 °C STEAM 710 Materiali in tehnologije / Materials and technology 53 (2019) 5, 705–710