UDK 621.762:669.018.9 ISSN 1580-2949 Original scientific article/Izvirni znanstveni članek MTAEC9, 44(5)251(2010) PREPARATION AND STUDY OF Mg2Sn-BASED COMPOSITES WITH DIFFERENT COMPOSITIONS PRIPRAVA IN KARAKTERIZACIJA LASTNOSTI KOMPOZITOV NA OSNOVI Mg2Sn Varužan Kevorkijan1, Sreco Davor Skapin2 1zasebni raziskovalec, Betnavska cesta 6, 2000 Maribor, Slovenia 2Srečo Davor Škapin, Institut "Jožef Stefan", Jamova 39, 1000 Ljubljana, Slovenia varuzan.kevorkijan@impol.si Prejem rokopisa - received: 2010-02-22; sprejem za objavo - accepted for publication: 2010-03-15 Single-phase Mg2Sn powders were successfully reaction-synthesized from the elements and applied for the preparation of Mg2Sn-based composites with different natures, microstructures and combinations of properties. These were fully dense (>95 % T.D.) Mg- and Al-metal-matrix composites (MMCs) reinforced with either Mg2Sn particles or mixtures of Mg2Sn with TiC or TiB2 particulates by the infiltration of porous Mg2Sn preforms with molten magnesium or aluminium; and (ii) Mg2Sn intermetallic matrix composites discontinuously reinforced with TiC and TiB2 particles by pressureless sintering. The microstructures of the composite samples were examined using scanning electron microscopy (SEM-EDS) and X-ray powder diffraction (XRD). The mechanical properties were evaluated by Vickers hardness measurements performed at room temperature, while the fracture toughness of the specimens was determined by applying the indentation method. Based on the data accumulated, an evaluation of the mechanical properties of these composites on the basis of the volume content of different constituents was performed. Moreover, the ability of various microstructures obtained with pressureless infiltration and sintering for tailoring the desired combination of mechanical properties. (e.g., toughening in combination with hardness) was also investigated and reported. Thus, the infiltration led to MMCs with different microstructures and mechanical properties, depending on the infiltrant applied. The samples infiltrated with molten magnesium possessed a characteristic lamellar, sometimes referred to as "Chinese script", eutectic microstructure and thereby an enhanced fracture toughness (up to 7.7 MPa m1/2in non-reinforced and 5.8 MPa-m1 in reinforced counterparts), in combination with a Vickers hardness superior to those of conventional Mg-Sn alloys. On the other hand, although the mechanical response (Vickers hardness) of the samples infiltrated with aluminium was even better than in the counterparts infiltrated with magnesium, the absence of the "Chinese script" microstructure was observed to have a detrimental influence on the fracture toughness, which was significantly lower in these samples. The densification of intermetallic matrix composites (IMCs) with a Mg2Sn matrix discontinuously reinforced with TiC or TiB2 ceramic reinforcement performed by non-reactive, solid-state sintering resulted in samples with a high density (>95% T.D.) and different combinations of mechanical properties compared to MMCs obtained by infiltration. The Vickers hardnesses of the sintered IMCs were much better than in the MMCs obtained by infiltration, with the exception of the fracture toughness, which was reduced below 1.8 MPa m1/2. Key words: Mg2Sn powder, synthesis, Mg2Sn-based composites, sintering, infiltration, microstructure development, hardness, fracture toughness Z reakcijo v trdnem smo iz elementov sintetizirali Mg2Sn. Spojino smo zdrobili in prah uporabili za pripravo vrste kompozitov z različnimi mikrostrukturnimi in mehanskimi lastnostmi. Pripravili smo goste kompozite (>95 % T. G.): (i) na osnovi kovinske matrice Mg in Al tako, da smo v porozne predoblike spojine Mg2Sn ter predoblike različnih sestav na osnovi Mg2Sn in TiC oziroma TiB2 infiltrirali tekoči Mg oziroma Al, in (ii) na osnovi intermeta ne spojine Mg2Sn, ki smo jih pripravili s sintranjem Mg2Sn z dodatkom ojačitvene faze trdin TiC oziroma TiB2. Mikrostrukturno analizo pripravljenih kompozitov smo opravili z vrstičnim elektronskim mikroskopom in elementno spektroskopsko disperzijsko analizo (EDS) ter z rentgensko praškovno difrakcijo. Mehanske lastnosti, trdoto po Vickersu in zlomno žilavost smo merili pri sobni temperaturi. Dobljene rezultate smo razložili glede na fazno sestavo pripravljenih kompozitnih vzorcev. Opisali smo odvisnost mehanskih lastnosti infiltriranih in sintranih vzorcev v odvisnosti od mikrostrukturnih karakteristik. Pri infiltraciji nastajajo kompoziti s kovinsko matrico (KKM) z različno mikrostrukturo in mehanskimi lastnostmi, kar je odvisno od uporabljene kovine, ki jo infiltriramo. Kompoziti na osnovi Mg izkazujejo lamelarno evtektično mikrostrukturo (kitajska pismenka) in izboljšano zlomno žilavost (do 7,7 MPa m12 neojačani materiali in 5,8 MPa m12 ojačani kompozitni materiali) in tudi višjo trdnost po Vickersu glede na komercialne Mg-Sn zlitine. Kompoziti na osnovi infiltriranega Al izkazujejo višjo trdnost kot Mg kompoziti, vendar pa nižjo zlomno žilavost, ker ne tvorijo lamelarne mikrostrukture. Pri sintranju kompozitov na osnovi intermetalne Mg2Sn-matrice, ki so bili ojačani s TiC oziroma TiB2 nastajajo gosto sintrani kompozitni materiali (>95 % T. G.) z različnimi mehanskimi lastnostmi. Trdota teh materialov je večja, kot jo izkazujejo kompoziti na osnovi kovinske matrice, vendar pa imajo manjšo zlomno žilavost, manj kot 1,8 MPa m1/2. Ključne besede: Mg2Sn-prah, priprava, kompoziti na osnovi Mg2Sn, sintranje, infiltracija, razvoj mikrostrukture, trdota, prelomna žilavost 1 INTRODUCTION resistant magnesium alloys, Mg2Sn precipitates are applied as a thermally stable intermetallic phase for Current applications of magnesium stannide (Mg2Sn) are limited to the optimisation of the microstructure and suppressing the grain-boundary sliding and dislocation mechanical properties of magnesium 17 and in lead-free movement, resulting in an improvement of the creep aluminium alloys 8. In the Mg-Sn and Mg-Sn-Ca creep- properties. However, due to its high melting point (770 °C), relatively low density (3.59 g/cm3 - about half that of the density of tin), excellent compressibility (2.83 10-11 m2/N, approximately 50 % higher than for Mg2Si) and a thermal expansion coefficient (9.9 10-6 K-1) similar to some borides and carbides 9,10, magnesium stannide is a promising structural material, particularly in combination with magnesium and aluminium alloys and composites. The Vickers hardness of Mg2Sn is about 1.2 GPa7, significantly lower than for Mg2Si (3.5-7.0 GPa), but still twice as high in comparison with the hardness of Mg-Sn alloys. In addition, Mg2Sn is a stoichiometric compound suitable for achieving characteristic eutectic microstruc-tures (i.e., "Chinese-script") and therefore for tailoring the properties of composites (particularly the fracture toughness) with Mg2Sn appearing as a matrix or a reinforcement phase. In contrast to numerous investigations carried out in developing Mg-Sn alloys with Mg2Sn precipitates formed in situ, only a limited number of investigations were concerned with the synthesis of Mg2Sn powder 11 and, to the best of our knowledge, none with its densifi-cation, alone or with some other reinforcing phases, i.e., as a matrix for high-temperature composites or as particulate reinforcement in metal matrix composites. Hence, in the present study, the following investigations were performed in order to demonstrate the potential of Mg2Sn as an advanced composite matrix or discontinuous reinforcement: (i) the synthesis of Mg2Sn single-phase powder from the elements; (ii) pressureless sintering and characterisation of Mg2Sn-based inter-metallic matrix composites discontinuously reinforced with TiC or TiB2 particles, and (iii) the formation and characterisation of Mg- or Al-metal matrix composites reinforced with either Mg2Sn particles or mixtures of Mg2Sn with TiC or TiB2 particulates by the infiltration of porous Mg2Sn preforms with molten magnesium and aluminium. 2 EXPERIMENTAL In the first part of the experimental work, Mg2Sn powder was synthesized with a reaction synthesis from the elements. As the source of magnesium and tin, cylindrical samples machined from pure magnesium and tin rods were used. Magnesium and tin samples in three different molar ratios (stoichiometric, with 5 % and 10 % excess of magnesium) were placed in a platinum crucible and heated in a vacuum furnace (for 2 h at 660 °C or for 1 h at 700 °C) in a static atmosphere of argon. This was followed by cooling to room temperature and characterisation of the as-obtained product with optical and scanning electron microscopy (OM and SEM) and X-ray diffraction (XRD). After that, the product was milled in an attrition mill for various milling times (0.5-2 h) in order to achieve the desired morphology of the Mg2Sn particles. The as-milled Mg2Sn powders were then applied for various infiltration and sintering experiments. The infiltration was performed by using porous preforms made from laboratory synthesized Mg2Sn powder of grade C (Table 1) and mixtures of Mg2Sn powder grade C and commercially available TiC (99.5 %, d50 = 4 pm) and TiB2 powders (99.5 %, d50 = 6 pm), as listed in Table 2. The preforms were isostatically pressed at various pressures (from 80 MPa to 150 MPa) in order to achieve samples with different porosities. The samples obtained were cylinders, 50 mm high and 20 mm in diameter. As infiltrant, Al-xSn and Mg-xSn (x = 3%, 5 %) alloys were applied. Al-xSn and Mg-xSn alloys necessary for infiltration were prepared from pure aluminium or magnesium and pure tin powders melted in a graphite crucible with the protection of a fusing agent. The melt was then stirred to ensure homogeneity and, finally, it was cast into a preheated mould. The as-cast ingots were cut and machined into thin cylindrical plates having the same diameter as the Mg2Sn preforms (20 mm). Finally, a preform sandwiched between two Al-xSn or Mg-xSn plates was placed in a ceramic crucible using the following procedure: the first Al-xSn or Mg-xSn plate was placed on the bottom of crucible and the preform was fixed on it using upper and lower preformatted steel plates. After that, the upper Al-xSn or Mg-xSn plate was placed on it. The volume of the Al-xSn or Mg-xSn plates was calculated to be approximately 50 % higher than the volume of the pores in the preform. The infiltration was conducted by heating the assembly in a vacuum furnace at 730 °C for 1 h, under a static atmosphere of argon. After completion of the infiltration, the assembly was cooled to room temperature, and then the infiltrated preform was removed from the furnace. The green samples for sintering experiments were formulated by blending the synthesized Mg2Sn powder (grade C, Table 1) with commercial ceramic powders (TiC and TiB2) in appropriate amounts to create IMCs with mass fractions w = (10, 30 and 50) % of TiC or TiB2 reinforcement. The powder blends were thoroughly mixed in a planetary mill and subsequently cold compacted. In all cases, the sintering of the compacts was conducted at 750 °C for 1 h in a static atmosphere of argon using a vacuum furnace. The as-synthesized composite samples were cut, machined and polished in accordance with standard procedures. Microstructural characterization of the fabricated composites was performed with OM and SEM, whereas XRD measurements were applied to the samples to identify the phases and their crystal structure. A quantitative determination of the volume percentage of Mg2Sn and ceramic particles in the matrix, as well as the retained porosity, was performed with an assessment of optical and scanning electron micrographs of polished composite bars using the point-counting method and image analysis and processing software. The composite density measurements were carried out using Archimedes' principle, applying absolute ethanol as the immersion fluid. The initial density of the green compacts (preforms and tablets) was calculated from the mass and geometry of the samples. Vickers hardness (HV) measurements were performed at room temperature on polished composite samples and calculated as the average of six indentations. These measurements were made with a conventional Vickers tester (load: 9.8-24.5 N for 15 s). Due to their small dimensions and high brittleness, the fracture toughness of the specimens obtained was determined by applying the indentation method 12. The Kic of the composite samples was determined from sub-micron-derived indentation cracks and calculated according to the equations proposed by Niihara et al. 13. 3 RESULTS AND DISCUSSION 3.1 Mechanism of the formation, chemical composition and morphology of laboratory-prepared Mg2Sn powder Depending on the initial composition of the reaction mixture and the heating conditions, the concentration of Mg and Sn impurities in the synthesized Mg2Sn phase varied significantly. On applying reaction mixtures with a stoichiometric ratio of elemental magnesium and tin, more than w = 5 % of the tin remained in the reaction product obtained (Mg2Sn powder grade A, Table 1), which was most probably caused by a loss of magnesium. This assumption was additionally confirmed by the experimental finding that the amount of non-reacted tin increased with the increasing temperature of the synthesis. Table 1: Phase composition and morphology of laboratory-prepared Mg2Sn powders Tabela 1: Fazna sestava in morfologija laboratorijsko izdelanih Mg2Sn prahov Powder ^(Mg2Sn)/% ^(Sn)/% d50/^m Grade A 95 5 3.3 Grade B 97 3 2.4 Grade C 99.8 0.2 2.1 On the other hand, by applying a reaction mixture with a small (x = 5 %) excess of magnesium, the amount of non-reacted tin was reduced below 5 % or even below w = 3 % (mass fractions) (grade B, Table 1) at a lower temperature of synthesis (660 °C). Finally, by using a reaction mixture with the mol fraction x = 10 % excess of magnesium, single-phase Mg2Sn (grade C, Table 1) with no Mg or Sn peak detected in the XRD pattern was prepared at 700 °C. The investigation of the solidified product samples indicated that the reaction mechanism of the Mg2Sn synthesis is homogeneous nucleation and growth. Based on the phase diagram of the Sn-rich corner in the Mg-Sn binary system 14, it is evident that Mg will start to dissolve into the liquid phase immediately after the temperature exceeds the melting point of Sn (505 K). With increasing temperature, a greater amount of Mg will be dissolved and, after melt saturation, the Mg2Sn will start to nucleate according to reaction 1: Mg(s) + Sn,,, = Mg2Sn, '(l) ■ (1) Above the melting point of magnesium (923 K), the nucleation of Mg2Sn will continue by nucleation from the saturated liquid phase according to reaction 2: Mg(l) + Sn(l) = Mg2Sn(s) (2) Thus, to achieve the complete conversion of reactants into Mg2Sn, it is important to preserve a permanent excess of magnesium (approximately w = 10 %) in the system up to the end of the synthesis. The morphology of the laboratory-prepared Mg2Sn powder, obtained with milling the solidified sample from reactive synthesis, is presented in Figure 1. As is evident, the powder obtained is non-agglomerated, with well-shaped individual particles with a size below 5 pm. The typical phase composition in the synthesized Mg2Sn powders is reported in Table 1. The compositions of various Mg2Sn-TiC and Mg2Sn-TiB2 mixtures used for preforms in the infiltration experiments are listed in Table 2. Table 2: The composition of various Mg2Sn-TiC and Mg2Sn-TiB2 mixtures used for preforms preparation in the infiltration experiments Tabela 2: Sestava različnih zmesi Mg2Sn-TiC in Mg2Sn-TiB2, uporabljenih za pripravo predoblik Mixture Initial composition, #1 100 % Mg2Sn (grade C) #2 75 % Mg2Sn (Grade C)-25 % TiC #3 75 % Mg2Sn (Grade C)- 25 % TiB2 #4 70 % Mg2Sn (Grade C)-30 % TiC #5 70 % Mg2Sn (Grade C)-30 % TiB2 3.2 Composites made by pressureless infiltration 3.2.1 Al-Mg2Sn(p) and Mg-Mg2Sn(p) The infiltration of porous Mg2Sn preforms (composition #1, Table 2) with molten Al resulted in fully dense composite samples with a continuous aluminium-based matrix, reinforced with Mg2Sn particles and Mg2Sn precipitates appearing near the primary Mg2Sn particles, Figure 2a. On the other hand, samples fully infiltrated with molten magnesium have a characteristic lamellar "Chinese script" eutectic microstructure, Figure 3a, and completely different mechanical properties, Table 3. In both cases, due to the complete and non-reactive wetting of the Mg2Sn preform skeleton with molten Mg or Al, under atmospheric pressure the infiltration proceeded spontaneously. The absence of chemical reactions between the preform skeleton and the molten infiltrants Figure 1: a) SEM micrograph of MgaSn powder (grade B) after milling, b) SEM micrograph of as-synthesized MgaSn and c) X-ray powder diffraction pattern of the prepared compound MgaSn: A -grade B powder (Table 1), and B - grade C powder (Table 1) Slika 1: a) SEM-posnetek MgaSn prahu (tip B) po mletju, b) SEM-posnetek vzorca MgaSn pred mletjem in c) XRD-difraktogram sinte-tizirane MgaSn-spojine: A - tip B (Tabela 1) in B-tip C (Tabela 1) Figure 3: a) SEM micrograph and b) X-ray powder diffraction pattern of the Mg2Sn-Mg composite sample infiltrated at 730 °C showing a lamellar structure consisting of Mg2Sn "Chinese-script" in a matrix of magnesium Slika 3: a) SEM-posnetek in b) XRD-difraktogram Mg2Sn-Mg-kom-pozita, infiltriranega pri 730 °C z značilno lamelarno mikrostrukturo ojačitve v Mg matriki Figure 2: a) SEM micrograph and b) X-ray powder-diffraction pattern of the pressurelessly infiltrated Mg2Sn-Al composite sample Slika 2: a) SEM-posnetek in b) XRD-difraktogram Mg2Sn-Al-kom-pozita, pripravljenega z infiltracijo Figure 4: a) SEM micrograph and b) XRD spectrum of pressureless infiltrated Al-Sn-Mg2Sn(p)-TiC(p) composite sample with an initial composition of the preform skeleton of f = 69 % Mg2Sn, f = 29 % TiC and f = 2 % Al (volume fraction f/%) Slika4: a) SEM posnetk in b) XRD difraktogram vzorca Al-Sn-Mg2Sn(p)-TiC(p) - kompozita, izdelanega z infiltriracijo predoblike na osnovi 69 % Mg2Sn, 29 % TiC in 2 % Al (volumenski delež f/%) Table 3: Average room-temperature Vickers hardness and fracture toughness of Al-MgaSn composites prepared by pressureless infiltration Tabela 3: Povprečne vrednosti trdote po Vickersu in prelomne žilavosti, izmerjene pri sobni temperaturi na vzorcih Al-MgaSn-kompozitov, izdelanih s postopkom infiltracije Composite composition Retained porosity Density p/(g/cm3) Vickers hardness (GPa) Kic/ (MPa m1/2) 18 % Al-82 % Mg2Sn 2.2 ± 0.2 3.5 ± 0.4 0.87 ± 0.09 3.4 ± 0.4 29 % Al-71 % Mg2Sn 3.5 ± 0.4 3.4 ± 0.3 0.82 ± 0.08 4.7 ± 0.5 38 % Al-62 % Mg2Sn 4.7 ± 0.5 3.3 ± 0.3 0.75 ± 0.08 5.3 ± 0.5 19 % Al-81 % Mg2Sn 2.0 ± 0.2 3.6 ± 0.4 0.88 ± 0.09 3.9 ± 0.4 28 % Al-72 % Mg2Sn 3.2 ± 0.3 3.5 ± 0.4 0.83 ± 0.08 4.8 ± 0.5 38 % Al-62 % Mg2Sn 3.9 ± 0.4 3.4 ± 0.3 0.79 ± 0.08 5.6 ± 0.6 Table 4: Average room-temperature Vickers hardness and fracture toughness of Mg-Sn-Mg2Sn composites prepared by pressureless infiltration Tabela 4: Povprečne vrednosti trdote po Vickersu in prelomne žilavosti, izmerjene pri sobni temperaturi na vzorcih Mg-Sn-Mg2Sn-kompozita, izdelanega s postopkom infiltracije Composite composition Retained porosity Density p/(g/cm3) Vickers hardness (GPa) Kic/ (MPa m1/2) 20 % Mg-80 % Mg2Sn 2.2 ± 0.2 3.3 ± 0.3 0.66 ± 0.07 4.7 ± 0.5 28 % Mg-71 % Mg2Sn 3.5 ± 0.4 3.1 ± 0.3 0.72 ± 0.07 6.5 ± 0.7 41 % Mg-59 % Mg2Sn 4.7 ± 0.5 2.9 ± 0.3 0.77 ± 0.08 7.3 ± 0.7 19 % Mg-81 % Mg2Sn 2.0 ± 0.2 3.4 ± 0.4 0.61 ± 0.06 5.4 ± 0.5 31 % Mg-69 % Mg2Sn 3.2 ± 0.3 3.1 ± 0.4 0.69 ± 0.07 6.6 ± 0.7 38 % Mg-62 % Mg2Sn 3.9 ± 0.4 3.0 ± 0.3 0.71 ± 0.07 7.7 ± 0.8 was proved with the corresponding X-ray diffraction patterns, Figures 2b and 3b. As evident from Tables 3 and 4, the Vickers hardnesses of the Al-MgaSn and Mg-MgaSn MMCs are improved with increasing the amount of MgaSn particulate reinforcement. However, regarding the fracture toughness, quite the opposite behaviour was observed. The fracture toughness of Al-MgaSn and Mg-MgaSn MMCs decreases with an increasing amount of MgaSn particu-lates. Comparing the mechanical properties of the Al-Mg2Sn and Mg-MgaSn MMCs, it is found that the Vickers hardness is evidently better in the samples infiltrated with aluminium. However, the fracture toughness is an exception, becoming greater (almost doubled) in the samples infiltrated with magnesium. The extraordinary fracture toughness of Mg-Mg2Sn MMCs is caused by their characteristic lamellar structure consisting of Mg2Sn "Chinese script" in a matrix of a magnesium solid solution. 3.2.2 Al-Mg2Sn(p)-TiC(p) and Al-Mg2Sn(p)-TiB2(p) Preforms made from mixtures of laboratory-synthesized Mg2Sn powder and commercially available TiC and TiB2 powders (compositions #1, #2, #3 and #4), were also successfully pressurelessly infiltrated with molten aluminium, resulting in samples with almost theoretical density and interesting combinations of mechanical properties. The microstructure of infiltrated samples consisted of a co-continuous network of Mg2Sn phase interpenetrated by an aluminium matrix with finely dispersed TiC or TiB2 particles, Figures 4 and 5. The absence of secon- dary phases, Figure 5b, indicates that in this case the spontaneous infiltration also proceeded as a non-reactive process. The reinforcement of an Al matrix with TiC or TiB2 particles resulted in a marked improvement in the Vickers hardness. As evident from Table 5, the Vickers hardness of Al-Mg2Sn-TiC and Al-Mg2Sn-TiB2 composites was approximately 50 % higher than in non-reinforced Al-Mg2Sn samples, Table 3. An examination of the fracture toughness, Table 5, revealed that the toughness of the MMCs was inversely proportional to the total amount of reinforcing phase. Moreover, it became lower when replacing some of the Mg2Sn particles with more brittle TiC or TiB2 particu-lates. This is well documented in Tables 3 and 5 for samples with approximately the same total amount of particulate reinforcement. 3.2.3 Mg -Mg2Sn(p)-TiC(p) and Mg-Mg2Sn(p)-TiB2(p) The experiments showed that the infiltration of Mg2Sn-TiC and Mg2Sn-TiB2 preforms with molten magnesium proceeded spontaneously, without a chemical reaction between the preform skeleton and the molten magnesium. By adjusting the porosity of the preforms within the range the volume fractions of 30 % to 35 %, composites with different compositions listed in Table 6 were routinely fabricated. At 900 °C, the infiltration was complete within 1h, resulting in composite samples with less than (p = 5 % of retained porosity. The resulting composite samples have a typical eutectic microstructure showing a lamellar structure consisting of Mg2Sn "Chinese script" in a matrix of Figure5: a) SEM micrograph and b) XRD spectrum of pressurelessly infiltrated Al-Sn-Mg2Sn(p)-TiB2(p) composite sample with an initial composition of the preform skeleton f = 75 % Mg2Sn, f = 25 % TiB2. Slika 5: a) SEM-posnetek in b) XRD-defraktogram vzorca Al-Sn-Mg2Sn(p)-TiB2(p) -kompozita, izdelanega iz predoblike na osnovi f = 75 % Mg2Sn in f = 25 % TiB2 Figure?: a) SEM micrograph and b) XRD spectrum of pressurelessly sintered Mg2Sn-Sn-TiC(p) composite sample with the initial composition f = 67 % Mg2Sn, f = 3 % Sn and f = 30 % TiC Slika7: a) SEM-posnetek in b) XRD-difraktogram Mg2Sn-Sn-TiC(p) -kompozita, izdelanega s sintranjem vzorcev, sestavljenih iz f = 67 % Mg2Sn, f = 3 % Sn in f = 30 % TiC Figure6: a) SEM micrograph and b) XRD spectrum of Mg-Sn-Mg2Sn(p)-TiC(p) with an initial composition of the preform skeleton f = 70 % Mg2Sn and f = 30 % TiC Slika6: a) SEM-posnetek in b) XRD-defraktogram vzorca Mg-Sn-Mg2Sn(p)-TiC(p)-kompozita, izdelanega z infiltracijo predoblike na osnovi f = 70 % Mg2Sn in f = 30 % TiC magnesium solid solution, additionally reinforced with fine TiC or TiB2 particles, Figures 7a and 8a. From the X-ray diffraction patterns of the composite samples, it is evident (Figure 7b and 8b) that besides Mg2Sn reinforcement and irrespective of the matrix composition, no secondary phases were detected, which indicates that the pressureless infiltration of Mg2Sn preforms with molten Mg-Sn-based alloys was not chemically assisted. A detailed SEM examination of interface regions of all the samples also confirmed the absence of chemical reactions between the composite constituents listed above. Regarding the mechanical properties of the Mg-Mg2Sn-TiC and Mg-Mg2Sn-TiB2 composite samples, which are summarized in Table 6, an increase in the particulate content (Mg2Sn and TiC or TiB2) was observed to improve the Vickers hardness, while at the same time reducing the fracture toughness. In addition, the Vickers hardness of the Mg-Mg2Sn-TiC and Mg-Mg2Sn-TiB2 composite samples was found to be better than in the non-reinforced counterparts, while the fracture toughness was about 25 % lower. Compared to the Al-Mg2Sn-TiC or Al-Mg2Sn-TiB2 counterparts, the reduction of Vickers hardness is only slight. On the other hand, the fracture toughness of the Mg-Mg2Sn-TiC or Mg-Mg2Sn-TiB2 composites is almost twice as high as in their Al-Mg2Sn-TiC or Al-Mg2Sn-TiB2 counterparts, which is due to the lamellar structure consisting of the MgaSn "Chinese script" in a matrix of magnesium. 3.3 Composites made by pressureless sintering 3.3.1 Mg2Sn-Sn-TiC(p) and Mg2Sn-Sn-TiB2(p) composites made by pressureless sintering Pressureless sintering of green samples made either from as-milled MgaSn powders of grade A and B, Table 1, or mixed with various amounts of TiC or TiBa particles, resulted in dense composite specimens with a retained porosity of less than the volume fraction

95 % T.D.) metal matrix composites with a metallic matrix discontinuously reinforced with MgaSn and TiC or TiB2 particulates. The infiltration proceeded spontaneously, without detectable chemical reactions between the preform skeleton and the molten infil-trants. 5. The composite samples infiltrated with molten magnesium possessed the characteristic lamellar "Chinese script" eutectic microstructure, while in samples infiltrated with molten aluminium the appearance of fine Mg2Sn-Sn precipitates in an Al matrix, mostly in the vicinity of the initially introduced Mg2Sn particles, was observed. 6. In preforms with the addition of TiC or TiBa ceramic reinforcement, the microstructure development during the infiltration occurred in the same way as in their non-reinforced counterparts. Because of the low temperature of the preform infiltration (750 °C), the particulate reinforcements remained chemically inert in contact with molten magnesium or molten aluminium, resulting in a final microstructure of infiltrated composite samples the same as in the non-reinforced counterparts. The only difference was observed inside the Al or Mg phases, which were completely reinforced with TiC or TiBa particles. 7. The microstructure of the composite samples obtained by pressureless infiltration could be tailored to consist of a continuous aluminium or magnesium matrix, discontinuously reinforced with Mg2Sn of different morphologies (particulates in samples infiltrated with aluminium and the characteristic "Chinese script" eutectic phase in samples infiltrated with magnesium) and, when added, TiC or TiBa reinforcements. Such a microstructure design was projected in order to achieve an optimum combination of enhanced fracture toughness (particularly improved by the "Chinese script" phase appearing in samples infiltrated with magnesium), with tensile properties and a hardness superior to that of conventional Mg-Sn alloys. 8. The Vickers hardness was found to be better in samples infiltrated with aluminium than in counterparts infiltrated with magnesium. On the other hand, quite the opposite behaviour was found with regard to the fracture toughness. Due to their characteristic lamellar structure consisting of MgaSn as the "Chinese script" in the matrix, composite samples infiltrated with magnesium possessed an enhanced fracture toughness almost twice that of the counterparts infiltrated with aluminium, in which the MgaSn phase appeared as particulates. 9. Within each single group of infiltrated samples (i.e., samples with the same qualitative composition), the Vickers hardness was enhanced, while the fracture toughness decreased with an increasing total amount of particulate reinforcement. 10. Pressureless sintering of green samples from MgaSn powders with 3-5% of free Sn, or from mixtures of these powders with various amounts of TiC or TiBa particles, resulted in dense composite specimens with a porosity of less than the volume fraction (p = 5 %. In contrast, pressureless sintering of green samples from MgaSn powder without free Sn or a mixture of the same powder with various amounts of TiC or TiBa particles was found to be incomplete, with more than p = 10 % of porosity. 11. The composites obtained consisted of a continuous MgaSn matrix and TiC or TiBa ceramic particulate reinforcement dispersed around the sintered MgaSn grains and small Sn inclusions. In contrast, the microstructures of the dense, non-reinforced samples were uniform, with fully sintered MgaSn grains and Sn inclusions. 1a. During sintering, the formation of secondary phases was not observed. Densification of composite samples proceeded with non-reactive sintering, assisted by molten tin 13. The Vickers hardness of the sintered samples (inter-metallic matrix composites with a MgaSn matrix discontinuously reinforced with TiC or TiBa ceramic reinforcement) was significantly improved in comparison with the metal matrix composites obtained by infiltration. The exception was the fracture toughness, which in the sintered samples was reduced to approximately one-third or even one-quarter of the values measured in the metal matrix composites obtained by infiltration. 14. With densities higher than the density of aluminium and magnesium alloys, MgaSn-based composites have a limited potential for the weight reduction of structural parts. However, some of the MgaSn composites (especially Mg-MgaSn metal matrix composites) could offer a unique combination of properties, including the ability of the composite microstructure (lamellar, consisting of the MgaSn "Scinese script" in a magnesium solid solution) to develop a toughening mechanism in combination with improved tensile properties and hardness. Acknowledgement This work was supported by funding from the Public Agency for Research and Development of the Republic of Slovenia, as well as the Impol Aluminium Company and Bistral, d. o. o. from Slovenska Bistrica, Slovenia, under contract No. 1000-07-219308. 5 REFERENCES I N. Hort, Y. Huang, T. A. Leil, P. Maier, K. U. Kainer, Adv. Eng. Mat., 8 (2006) 5, 359 2N. Hort, Y. Huang, K. U. Kainer, F. Moll, K. U. Kainer, Adv. Eng. Mat., 8 (2006) 4, 235 34 J. Gröbner, A. Janz, A. Kozlov, Dj. Mirkovic, R. S. Fetzer, JOM, 60 (2009) 12, 32 4 M. Zhang, W. Z. Zhang, G. Z. Zhu, Scrpita Materialia 59 (2008), 866 5 Z. Min, Z. W. Zheng, Z. G. Zhen, Y. Kun, Trans. Nonferrous Met. China 17 (2007), 1428 6Z. X. Ping, C. Y. Gui, X. Y. HUa, Trans Nonferrous Met. Soc. China 18 (2008), s299 7 B. H. Kim, J. J. Jeon, K. C. Park, B. G. Park, Y. H. Park, I. M. park, Archives of Materials Science and Engineering, 30 (2008) 2, 93 8S. Koch, H. Antrekowitsch, BHM, 153 (2008) 7, 278 9O. Madelung, U. Rössler, M. Schulz, Non-tetrahedrally bonded elements and binary compounds I, Springer-Verlag, 1998, 1-3 10 C. Zhang, P. Han, X. Yan, C. Wang, L. Xia, B. Xu, J. Phys. D: Appl. Phys., 42 (2009), 1. (doi: 125403) II W. Y. Feng, D. W. Bo, Z. T. Young, Trans. Nonferrous Met. Soc. China, 19 (2009), 1196 12 K. Kondoh, H. Oginuma, T. Aizawa, Materials Transactions, 42 (2001), 1293 13 K. Niihara, R. Morena, D. P. Hasselman, J. Mater. Sci. Lett. 1 (1982), 13 14 A. A. Nayeb-Hasemi, J. B. Clark, J. Bull. Alloy Phase Diagrams 63 (1984), 467