<?xml version="1.0"?><rdf:RDF xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:edm="http://www.europeana.eu/schemas/edm/" xmlns:wgs84_pos="http://www.w3.org/2003/01/geo/wgs84_pos" xmlns:foaf="http://xmlns.com/foaf/0.1/" xmlns:rdaGr2="http://rdvocab.info/ElementsGr2" xmlns:oai="http://www.openarchives.org/OAI/2.0/" xmlns:owl="http://www.w3.org/2002/07/owl#" xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:ore="http://www.openarchives.org/ore/terms/" xmlns:skos="http://www.w3.org/2004/02/skos/core#" xmlns:dcterms="http://purl.org/dc/terms/"><edm:WebResource rdf:about="http://www.dlib.si/stream/URN:NBN:SI:doc-5D6LXSPB/4e73ef8e-e7ad-45f2-abe8-2491691d8d89/PDF"><dcterms:extent>1745 KB</dcterms:extent></edm:WebResource><edm:WebResource rdf:about="http://www.dlib.si/stream/URN:NBN:SI:doc-5D6LXSPB/4fb5b36c-671a-452f-a0b9-0debea0ef4f5/TEXT"><dcterms:extent>0 KB</dcterms:extent></edm:WebResource><edm:ProvidedCHO rdf:about="URN:NBN:SI:doc-5D6LXSPB"><dcterms:issued>2026</dcterms:issued><dc:creator>Asci, Muhammet Ibrahim</dc:creator><dc:creator>Ermurat, Mehmet</dc:creator><dc:creator>Ince, Ibrahim Hakki</dc:creator><dc:format xml:lang="sl">številka:7/8</dc:format><dc:format xml:lang="sl">letnik:72</dc:format><dc:format xml:lang="sl">str. 214-227</dc:format><dc:identifier>ISSN:0039-2480</dc:identifier><dc:identifier>DOI:10.5545/sv-jme.2026.1646</dc:identifier><dc:identifier>COBISSID_HOST:292733699</dc:identifier><dc:identifier>URN:URN:NBN:SI:doc-5D6LXSPB</dc:identifier><dc:language>en</dc:language><dc:publisher xml:lang="sl">= Association of Mechanical Engineers and Technicians of Slovenia etc.</dc:publisher><dc:publisher xml:lang="sl">Zveza strojnih inženirjev in tehnikov Slovenije etc.</dc:publisher><dc:source xml:lang="sl">Strojniški vestnik</dc:source><dc:subject xml:lang="en">additive manufacturing</dc:subject><dc:subject xml:lang="en">continuous coaxial nozzle design</dc:subject><dc:subject xml:lang="en">directed energy deposition (DED)</dc:subject><dc:subject xml:lang="sl">dodajalna izdelava</dc:subject><dc:subject xml:lang="en">particle tracing</dc:subject><dc:subject xml:lang="sl">sledenje delcev</dc:subject><dc:subject xml:lang="sl">usmerjeno nanašanje (DED)</dc:subject><dc:subject xml:lang="sl">zasnova zvezne koaksialne šobe</dc:subject><dc:title xml:lang="sl">Design-based assessment of continuous coaxial DED nozzles considering substrate-induced gas flow effects|</dc:title><dc:description xml:lang="sl">Continuous coaxial nozzles are widely used in directed energy deposition (DED) processes. However, many numerical studies rely on substrate-free free-jet models that fail to capture critical gas–surface interactions. This study presents a design-oriented investigation of continuous coaxial DED nozzles by examining the influence of nozzle geometry and gas flow interactions under realistic deposition conditions. A three-dimensional CFD framework incorporating particle tracing was applied, in which a physical substrate was explicitly included at the intended standoff distance to account for stagnation pressure formation, gas rebound, and near-wall flow effects. Two nozzle geometries, a narrow nozzle (ß = 24°) and a wide nozzle (ß = 35°), were evaluated under varying carrier and shaping gas velocities relative to a fixed optical shielding gas velocity. Powder convergence behavior was quantified using a layered particle counting strategy and analyzed through number density distributions in the focal region. The results show that nozzle geometry strongly governs powder focusing behavior. The narrow nozzle consistently produced a compact and axisymmetric powder stream with higher catchment efficiency, whereas the wide nozzle exhibited diffuse flow patterns and reduced focal coherence. Excessive shaping gas velocities were found to degrade convergence by expanding the substrate-induced stagnation pressure zone. These findings provide a physics-based rationale for geometry-dependent nozzle selection in continuous coaxial DED applications</dc:description><dc:description xml:lang="sl">Zvezne koaksialne šobe se pogosto uporabljajo pri usmerjenem nanašanju materiala (DED), vendar številne numerične raziskave temeljijo na modelih prostega curka brez substrata, ki ne zajamejo ključnih interakcij med plinom in površino. Ta študija zajema raziskavo zasnove zvezne koaksialne šobe in vpliva njene oblike ter interakcije toka plina v realnih pogojih nanašanja. Uporabljen je bil tridimenzionalni CFD-model s sledenjem delcev. Model vključuje tudi substrat na ustrezni razdalji od šobe in tako upošteva nastanek zastojnega tlaka, povratni tok plina in učinke toka v bližini stene. Analizirani sta bili dve obliki šob: ozka šoba (ß = 24°) in široka šoba (ß = 35°), pri različnih hitrostih nosilnega in oblikovalnega plina ter konstantni hitrosti zaščitnega plina. Konvergenca curka prahu je bila ovrednotena z večplastno metodo štetja delcev in analizirana na podlagi porazdelitve njihove številske gostote v območju gorišča. Rezultati kažejo, da oblika šobe pomembno vpliva na konvergenco curka prahu. Ozka šoba je dosledno zagotavljala kompakten in osno simetričen curek prahu z večjim izkoristkom prahu, medtem ko je široka šoba povzročila bolj razpršen curek prahu in slabšo konvergenco. Ugotovljeno je bilo tudi, da previsoke hitrosti oblikovalnega plina poslabšajo konvergenco zaradi širjenja območja zastojnega tlaka nad substratom. Ugotovitve raziskave predstavljajo fizikalno utemeljeno osnovo za izbiro oblike zvezne koaksialne šobe za DED proces</dc:description><edm:type>TEXT</edm:type><dc:type xml:lang="sl">znanstveno časopisje</dc:type><dc:type xml:lang="en">journals</dc:type><dc:type rdf:resource="http://www.wikidata.org/entity/Q361785" /></edm:ProvidedCHO><ore:Aggregation rdf:about="http://www.dlib.si/?URN=URN:NBN:SI:doc-5D6LXSPB"><edm:aggregatedCHO rdf:resource="URN:NBN:SI:doc-5D6LXSPB" /><edm:isShownBy rdf:resource="http://www.dlib.si/stream/URN:NBN:SI:doc-5D6LXSPB/4e73ef8e-e7ad-45f2-abe8-2491691d8d89/PDF" /><edm:rights rdf:resource="http://rightsstatements.org/vocab/InC/1.0/" /><edm:provider>Slovenian National E-content Aggregator</edm:provider><edm:intermediateProvider xml:lang="en">National and University Library of Slovenia</edm:intermediateProvider><edm:dataProvider xml:lang="sl">Univerza v Ljubljani, Fakulteta za strojništvo</edm:dataProvider><edm:object rdf:resource="http://www.dlib.si/streamdb/URN:NBN:SI:doc-5D6LXSPB/maxi/edm" /><edm:isShownAt rdf:resource="http://www.dlib.si/details/URN:NBN:SI:doc-5D6LXSPB" /></ore:Aggregation></rdf:RDF>