181 Original scientific paper  MIDEM Society Computer Simulation Model for Evaluation of Radiation and Post-Irradiation Effects in Voltage Regulator with Vertical PNP Power Transistor Vladimir Dj. Vukić University of Belgrade, Institute of Electrical Engineering “Nikola Tesla”, Belgrade , Serbia Abstract: The aim of the presented research was to develop a faithful SPICE simulation model of radiation and post-irradiation effects in a low-dropout voltage regulator with a vertical serial PNP transistor. The main parameters for the analysis of the circuit’s radiation response were the voltage regulator’s maximum output current and the minimum dropout voltage, as well as the serial transistor’s excess base current. All the data, comprised of the old irradiation and new annealing results, were unified and normalised, in order to enable a broad insight in the radiation tolerance of the examined circuits. Initial radiation effects, as well as the late post-irradiation effects, were successfully simulated using the variations of the maximum forward emitter current gain and knee current of the serial PNP power transistor. Ten-year room temperature annealing led to a significant recovery of the serial transistor’s excess base current, yet the maximum output current and minimum dropout voltage, in most cases, expressed further degradation. On the other hand, two short-term, high-temperature annealing periods led to the tremendous recovery of all of the irradiated voltage regulators, reducing the circuit degradation down to the level perceived after absorption of nearly 10% of the total ionising dose. Keywords: vertical PNP transistor; excess base current; forward emitter current gain; computer simulation; voltage regulator, ionising radiation. Računalniški simulacijski model za ocenjevanje sevalnih in post sevalnih vplivov na napetostni regulator z vertikalnim močnosnim tranzistorjem PNP Izvleček: Cilj raziskave je bil razvoj zanesljivega SPICE simulacijskega modela sevalnih vplivov na low-drop napetostni regulator z vertikalnim serijskim tranzistorjem PNP . Glavni parametri analize odziva regulatorja na sevanje je bil največji izhodni tok in najnižja napetostna razlika med vhodom in izhodom (dropout napetost) ter bazni tok tranzistorja. Vsi podatku skupaj z rezultati starega sevanja in toplotne obdelave, so bili poenoteni in normalizirani za lažji vpogled v sevalno odpornost vezij. Začetni sevalni vplivi, kakor tudi post-sevalni vplivi, so bili uspešno simulirani s spreminjanjem ojačenja emitorskega toka in kolenskega toka tranzistorja PNP . Deset letna temperaturna obdelava pri sobni temperature je vodila k očitni ozdravitvi tranzistorskega baznega toka. Največji izhodni tok in najnižja dropout napetost je v večini primerov pokazala dodatno degradacijo. Po drugi strani pa sta dve kratkotrajni visokotemperaturni obdelavi pokazali občutno ozdravljenje obsevanih napetostnih regulatorjev, pri čemer je bila degradacija vezja ob 10% sevalni dozi zanemarljiva. Ključne besede: vertikalni tranzistor PNP; bazni tok; ojačenje emitorskega toka; simulacije; napetostni regulator; ionsko sevanje. * Corresponding Author’s e-mail: vvukic@ieent.org Journal of Microelectronics, Electronic Components and Materials Vol. 48, No. 3(2018), 181 – 193 1 Introduction Despite the increasing use of switching power sup- plies, linear voltage regulators still have a wide area of use in electronic devices, particularly in battery-pow- ered systems [1]. This also applies to radiation-tolerant electronic devices, used in radiation environments such as satellites, nuclear and medical facilities as well as in the military environment. Bipolar transistors [2-5] 182 V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 and analogue integrated circuits [6, 7] (including volt- age regulators [8-11]) have been extensively examined in the radiation fields, particularly following the discov- ery of the enhanced low-dose-rate sensitivity (ELDRS) in bipolar transistors [12, 13]. Since the cost of dedicated radiation-tolerant integrat- ed circuits is very high, in recent years extensive efforts have been made to identify commercial off-the-shelf (COTS) integrated circuits (and related technology pro- cesses) suitable for application in radiation environ- ments [14]. Among the tested circuits is the low-drop- out voltage regulator STMicroelectronics ® L4940V5, a circuit with a vertical PNP pass transistor [15], founded on the complementary BiCMOS process [16]. The circuit demonstrated unexpectedly high radiation tolerance [17-21], qualifying itself as a serious COTS candidate for use in moderate-dose radiation environments [17, 18]. Nevertheless, there were not enough data to cre- ate a faithful computer simulation model. Also, there were no detailed experiments that could quantify the circuit’s post-irradiation response. In order to provide a wider picture on the radiation and post-irradiation effects in the L4940V5 voltage regula- tor, various isothermal annealing procedures were im- plemented. After long-term room temperature anneal- ing, two short-term isothermal annealing procedures were performed. Also, a computer simulation model was developed in order to model the response of the vertical serial PNP power transistor. These combined ef- forts should enable the acquisition of comprehensive knowledge on the L4940V5 voltage regulator’s radia- tion response. 2 Theory 2.1 Radiation effects Ionising radiation affects silicon bipolar junction tran- sistors mainly through the mechanisms of charge- trapping, both in the oxide and on the semiconductor- oxide interface [14, 22]. The excess base current is the most important measure of the radiation-caused deg- radation of the bipolar junction transistor. It represents the difference between the base current measured af- ter irradiation (I B ) and the base current prior to irradia- tion (I B0 ) [14]: ΔI B = I B – I B0 (1) The base current has two components, the ideal one (I Bi ), affecting the transistor’s current gain, and the re- combination component (I Br ), being the current of only the internal recombination processes in the base area [8, 23]: T e EB T EB V n V Se nV V S Br Bi B e I e I I I I + = + = (2) where: I S – transport saturation current [24], I Se – emit- ter-base leakage current, V EB – emitter-base voltage, V T – thermal voltage (being 26 mV at the room temperature of 20°C), n – ideality factor of the ideal base current, n e – ideality factor of the recombination base current (or, in SPICE models, emitter-base leakage emission coef- ficient [24]). Excess base current may be presented as the difference between the pre-irradiation and post-irradiation base currents. The detailed relation for the excess base cur- rent is [25]:         − = Δ                 T EB T eff V V d V V dB E i B e W s e x s P qn I 2 2 ' " 2 1 (3) where: s’ – pre-irradiation surface recombination veloc- ity, s” – post-irradiation surface recombination velocity, W d – width of the depletion area in the base-emitter area prior to irradiation, q – elementary electron charge (1.6·10 -19  C), n i – intrinsic carrier concentration in silicon, x dB – location of the depletion region at the surface of the base, P E – emitter perimeter, V eff – effective voltage (used in place of V EB , in order to include the influence of the oxide-trapped charge on the total voltage on the emitter-base junction) [25]. The excess base current rises proportionally to the difference of the surface re- combination velocities existing prior to and after the exposure to ionising radiation. For a heavily-doped emitter and low emitter-base voltage (up to 0.6 V) [26], the excess base current may be considered to be di- rectly proportional to the increase of the concentration of interface traps [26, 27]. Nevertheless, the excess base current cannot be affected only by the interface traps. The influence of the oxide-trapped charge is particu- larly important in the cases when the emitter was not heavily doped. Build-up of the oxide-trapped charge will increase the surface potential of the P-type emitter area [25]. Therefore, the surface recombination veloc- ity depends on both the interface traps and the oxide traps. The ideality factor for the ideal base current is n = 1, but its value is not constant for the recombination cur- rent. Usually, the ideality factor of the recombination current is considered to be n e = 2, the same as during the normal operation of the transistor with a high emit- ter injection level [22]. Nevertheless, in reality, the re- 183 combination current ideality factor has variable values between 1 and 2. Despite the long-known fact that the ideality factor is dependent on the applied base- emitter voltage [26], this fact is neglected in standard computer simulation models. In NPN bipolar transistors, the P-type base, right be- neath the isolation oxide, is the most sensitive area. The reason is the relatively low doping concentration of the P-base, in comparison with the N-type collector and emitter. Both oxide-trapped charge and interface traps would negatively affect the P-type base, causing a rise in the excess base current [23]. On the other hand, in PNP transistors, the N-type base is not so endangered, since the positive oxide-trapped charge will cause the electrons to accumulate in the base area, suppressing the negative effects of the interface traps during the initial phase of irradiation [25]. If the emitter area is not heavily implanted, it will be the area most affected by the influence of radiation, experiencing the negative influence of both interface traps (increasing the sur- face recombination in silicon) and oxide traps (causing the depletion of the emitter area beneath the oxide) [28]. Mutually, these effects cause the depletion region on the base-emitter junction to spread deep into the emitter area, affecting the rise in the excess base cur- rent [28]. The mentioned effects depend on many fac- tors, such as doping concentrations, the geometry of the transistors, the quality of oxides and passivation layers, etc. During the exposure to radiation of the silicon bipolar junction transistors, the initial phase will be dominated by the influence of the oxide-trapped charge [25]. At the same time, the concentration of the charge trapped at the interface between the silicon and silicon-dioxide will rise much more slowly, affecting the rise in the ex- cess base current almost proportionally to the total ab- sorbed dose [25]. Yet, after some time has elapsed in the ionising radiation field, the surface recombination velocity will reach its limit and the excess base current will enter the saturation phase. 2.2 Annealing Stability of defects in semiconductors and oxides, caused by radiation, depends on time, electric field and temperature [22]. Thus, a concentration of defects in materials may significantly change after irradiation, with tendency to substantially reduce in high-temper- ature ambient [22]. Depending on the nature of radia- tion and trapped charge (both in oxide and a semi- conductor-oxide interface), bipolar transistors may partially recover or even further degrade its character- istics. Analysis of post-irradiation, time-dependent ef- fects should provide a more detailed insight into the radiation response of the circuits exposed. Thermal ex- citation usually leads to a significant defect annealing at temperatures of 100°C and greater, while the tun- neling is a dominant effect at a room temperature [22]. Several procedures were usually used, based either on isothermal [14] or isochronal [22] annealing. Isother- mal annealing procedures are performed at a constant temperature (either room or elevated) [14], and this approach often enables a qualitative evaluation of the radiation-induced defects. On the other hand, isochro- nal annealing is performed with constant, successive time intervals [22], usually much shorter than the ones used for isothermal examinations. Isothermal anneal- ing is a more realistic test procedure, since it may simu- late a real exploitation conditions, in periods from one day up to several years. On the other hand, isochronal annealing procedures may involve high temperatures, yet in much shorter time intervals (in order of minutes). According to the published data [29], some integrated circuits showed annealing of the trapped holes from the oxide after the end of the elevated temperature (100°C) isothermal annealing, without a significant ef- fect on the interface traps. Therefore, it would be pos- sible for some devices to express radiation-induced degradation originating only from the influence of in- terface traps [29]! 3 Materials and methods Analysis of irradiation and isothermal annealing effects was performed on integrated 5-volt, positive voltage regulators STMicroelectronics ® L4940V5. Samples were irradiated in the 60 Co ionising radiation field in the Vinča Institute of Nuclear Sciences, Belgrade, Serbia, in the Metrology-Dosimetry Laboratory [17-19]. The devices absorbed total γ-radiation doses of 500 Gy(SiO 2 ), at a dose rate of 4 cGy(SiO 2 )/s [20, 21]. For nearly ten years, the irradiated samples were kept in the office locker, at a room temperature always kept in the range 15–25°C. After 85,000 hours, all the samples of voltage regula- tors were tested in the same conditions as immediately after the irradiation, with a room temperature of 20°C. Shortly afterwards, the L4940V5 voltage regulators were examined to see if it would be possible to recover most of the oxide-trapped charge after one-week’s annealing at the temperature of 100°C, with a negli- gible effect on the interface traps. Consequently, an- other one-week annealing at 150°C should lead to the complete recovery of all the radiation-induced oxide- trapped charge and most of the interface traps. The primary examined parameters were the voltage regulator’s maximum output current, the serial transis- V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 184 tor’s minimum dropout voltage and the total circuit’s quiescent current. Measurement of the quiescent cur- rent enabled the calculation of the serial transistor’s base current and, consequently, the serial transistor’s forward emitter current gain [18, 20, 21]. Voltage and current vaweforms were recorded using the oscillo- scope Fluke ® 196C. Several days after completion of the room-tempera- ture annealing experiment, the circuits were annealed in the thermal chamber, at a temperature of 100°C, uninterruptedly for 168 hours. After the seven-day an- nealing, a new round of experiments was performed, with the same electrical parameters recorded. Finally, a day after the completion of the second round of electrical measurements, a final isothermal annealing sequence was performed, for another 168 hours with the same samples in the thermal chamber, yet this time at a temperature of 150°C. After the completion of the last annealing phase, the final data set on annealed voltage regulators was recorded. The presented se- quence of isothermal annealing procedures, with the various temperatures and durations, should enable better insight into the influence of interface traps and the oxide-trapped charge on the radiation and post-ir- radiation response of a complex integrated circuit. Ten years should be a typical exploitation period for the electronic components in aerospace applications [22]. Since the manufacturer of the circuit L4940V5 did not provide the schematic circuit diagram of this voltage regulator, many efforts were made to gather the neces- sary data on the internal structure of this device. Using the published papers [30, 31] and patents [16, 32], the author created a basic computer simulation model in the program “LTspice IV” [33]. The created model was rigorously examined and improved until it enabled a pretty good recreation of a wide ensemble of experi- mental results. There was no intention to recreate all the details of the integrated circuit as made by its man- ufacturer, so it is not a straight replica of the particular circuit design. Yet, the presented simulation model was good enough to describe the circuit’s response to the influence of γ-radiation. In order to present the circuit’s response for various bias and load conditions, previously published results were unified with the data from new experiments. The data on the mean values of the maximum output current [17, 18], minimum dropout voltage [20, 21] and on-line parameters [19, 34], procured immediately after the ex- posure of the L4940V5 devices, were extensively pre- sented in previous years. However, new experiments on the isothermal annealing of the voltage regulator were done on the same samples, yet this time ten years later. So, in order to avoid the unnecessary repetition of the old data, mostly results normalised to the data on virgin devices are now presented. Yet, the creation of the computer simulation model, as well as in-depth analysis of the perceived radiation effects, was not pos- sible without unification of all the experimental data obtained. Descriptions of the experiments performed, the ra- diation sources, and the procedures implemented for procurement of the circuit’s electrical parameters are in the detail provided in the references [17–21, 34, 35]. 4 Results Table 1 summarises the results on maximum out- put current and minimum dropout voltage (for load currents of 100 mA and 400 mA), obtained in the γ-radiation field with various biases and loads during irradiation. From the data on the quiescent current in the examined circuits, as well as from data on unloaded voltage regulators, the values of the serial transistor’s base current and the internal control circuit’s con- sumption were calculated (in a positive voltage regu- lator with the PNP pass transistor, total quiescent cur- rent represents the sum of these two currents [18, 21]). Consolidated results were presented, showing, firstly, data on unexposed circuits, then the data procured af- ter absorption of total doses from 50 Gy up to 500 Gy, and, finally, the data procured during the isothermal annealing (long-term room-temperature, followed by short-term 100°C and 150°C annealing). Only the most important data necessary for the circuit response anal- ysis are presented in the table, and all data were nor- malised to the values of virgin devices. Therefore, since the data on unloaded voltage regulators had basically the same trends in all three cases, only data obtained during the examination of the maximum output cur- rent are presented. As previously reported on its radiation response [17- 21], and being valid also following the implemented annealing of the tested circuits, the voltage regulator kept stable output voltage in all the examined operat- ing points, regardless of the bias conditions during pre- vious irradiation. The voltage reference circuit suffered negligible degradation, since the variations of the out- put voltage in unloaded devices could be measured in millivolts [21, 34]. The waveforms of the input voltage, output voltage and quiescent current, recorded on the laboratory setup, were presented in Fig. 1. Despite the high alternate current components, measured values of direct current enabled successful evaluation of the voltage regulator’s radiation response. V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 185 Table 1: Relative values of serial transistor’s dropout voltage (V EC12 ; for tests with load current of 100 mA and 400 mA), maximum output current (I max ) and no-load quiescent current (I Q0 ), as well as the accompanying data on the absolute values of the serial transistor’s excess base current (ΔI B12 ) in voltage regulator STMicroelectronics ® L4940V5. Values were based on data recorded on virgin devices, during the exposure, and after irradiation, for the specified periods and types of isothermal annealing. Experimental results were extended with parameters of the serial transistor (maximum forward emitter current gain (β Fmax ) and knee current (I kF )), defined in the SPICE simulation models. Simulation models with serial PNP power transistors, having the parameters specified in the last two columns, were ones that reached high agreement with the data procured through all three types of experiment. Successive periods of isothermal an- nealing were marked as follows: annealing 1 (Θ a = 20°C, t = 85,000 hours); annealing 2 (Θ a = 100°C, t = 168 hours); annealing 3 (Θ a = 150°C, t = 168 hours). Basic values of serial transistor’s dropout voltage, base current and no-load quiescent current, experimentally procured on unexposed (D = 0 Gy) L4940V5 voltage regulators, for various bias and load conditions: a) 0 V, 0 A: V EC12 (100 mA) = 0.355 V [20], I B12 (100 mA) = 0.545 mA [20], V EC12 (400 mA) = 1.766 V [21], I B12 (400 mA) = 4.627 mA [21], I max = 835.9 mA [18], I Q0 = 3.753 mA [18], I B12 (max) = 20.397 mA [18]; b) 8V, 1 mA: V EC12 (100 mA) = 0.394 V [20], I B12 (100 mA) = 0.703 mA [20], V EC12 (400 mA) = 1.736 V [21], I B12 (400 mA) = 3.824 mA [21], I max = 855.1 mA [18], I Q0 = 3.772 mA [18], I B12 (max) = 19.028 mA [18]; c) 8 V, 100 mA: V EC12 (100 mA) = 0.392 V [20], I B12 (100 mA) = 0.734 mA [20], V EC12 (400 mA) = 1.763 V [21], I B12 (400 mA) = 4.417 mA [21], I max = 852.5 mA [18], I Q0 = 3.806 mA [18], I B12 (max) = 25.304 mA [18]; d) 8 V, 500 mA: V EC12 (100 mA) = 0.378 V [20], I B12 (100 mA) = 0.731 mA [20], V EC12 (400 mA) = 1.793 V [21], I B12 (400 mA) = 5.638 mA [21], I max = 820.5 mA [18], I Q0 = 3.806 mA [18], I B12 (max) = 25.304 mA [18]. STMicroelectronics® L4940V5 Type of experiment Simulation Operation during irradiation and annealing V EC12 (100 mA) V EC12 (400 mA) Imax Parameters of serial PNP power transistor, Q12 Bias and load during irradi- ation Dose, D [Gy] V EC12 [p.u.] I B12 [p.u.] ΔI B12 [mA] V EC12 [p.u.] I B12 [p.u.] ΔI B12 [mA] I max [p.u.] I Q0 [p.u.] I B12 [p.u.] ΔI B12 [mA] β Fmax I kF [A] 0 V 0 A 0 1 1 0 1 1 0 1 1 1 0 270 0.225 50 1.161 2.422 0.78 1.153 1.813 3.76 0.995 0.981 1.44 8.98 115 0.375 100 1.144 4.128 1.71 1.208 3.395 11.08 0.956 0.959 1.760 15.49 500 1.631 75.43 40.57 1.298 7.478 29.98 0.966 0.874 1.997 20.34 Annealing 1 1.27 3.996 1.63 1.265 3.127 9.84 0.862 0.933 2.118 22.8 Annealing 2 1.087 3.486 1.36 1.067 2.669 7.72 0.916 0.965 1.567 11.56 67 0.49 Annealing 3 1.234 2.312 0.64 1.08 1.659 1.82 0.898 0.967 1.28 5.71 125 0.38 8 V, 1 mA 0 1 1 0 1 1 0 1 1 1 0 340 0.225 50 1.023 1.55 0.39 1.11 1.349 1.34 0.999 0.986 1.089 1.7 180 0.375 100 0.990 2.119 0.79 1.139 1.938 3.59 0.993 0.976 1.435 8.27 115 0.425 200 1.000 3.599 1.83 1.127 3.894 11.07 0.980 0.954 1.785 14.94 45 1.1 300 1.003 5.747 3.34 1.242 6.859 22.41 0.974 0.938 1.870 16.55 500 1.251 27.89 18.91 1.347 8.567 28.94 0.958 0.917 1.904 17.2 Annealing 1 1.071 5.334 3.05 1.395 7.377 24.39 0.894 0.936 2.27 17.2 Annealing 2 1.071 3.115 1.49 1.187 2.712 6.55 0.937 0.962 1.904 11.71 60 0.7 Annealing 3 1.198 1.508 0.36 1.181 1.42 1.61 0.946 0.973 1.616 2.57 150 0.39 8 V, 100 mA 0 1 1 0 1 1 0 1 1 1 0 340 0.225 50 1.028 1.88 0.65 1.132 1.607 2.68 0.992 0.983 1.377 6.82 127 0.375 100 0.987 3.011 1.48 1.161 2.719 7.59 0.968 0.967 1.723 13.08 55 0.75 200 1.031 6.131 3.77 1.243 7.19 27.34 0.961 0.941 2.027 18.57 500 1.372 57.96 41.81 1.284 8.021 31.01 0.954 0.899 2.202 21.73 Annealing 1 1.372 11.38 7.62 1.336 7.63 29.28 0.891 0.922 2.065 19.26 Annealing 2 1.092 3.856 2.1 1.221 3.337 10.32 0.967 0.951 1.829 14.99 45 1 Annealing 3 1.115 1.703 0.52 1.188 1.535 2.36 0.934 0.967 1.326 5.9 120 0.4 8 V, 500 mA 0 1 1 0 1 1 0 1 1 1 0 240 0.2 50 0.971 1.929 0.68 1.085 1.591 3.33 1.007 0.98 1.164 4.15 100 0.375 100 1.011 3.010 1.47 1.153 2.914 10.79 0.999 0.962 1.289 7.32 500 1.704 54.56 39.15 1.267 6.297 29.86 1.01 0.909 1.427 10.8 Annealing 1 1.235 13.42 9.08 1.35 5.692 26.45 0.932 0.943 1.432 10.42 Annealing 2 1.103 3.844 2.08 1.25 3.663 15.01 0.969 0.956 1.368 9.32 Annealing 3 0.997 1.696 0.51 1.161 1.453 2.55 0.942 0.967 1.148 3.76 105 0.375 V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 186 Basic data on the vertical serial PNP power transistor, obtained using the SPICE simulations, are also included in Table 1. Since the previous research concluded that the control circuit did not have a significant influence on the voltage regulator’s radiation response [20, 21], the focus of the computer simulation analysis was on the serial power transistor. The primary influence on the L4940V5 voltage regulator’s radiation hardness was the interdigitated structure of its serial PNP transistor [17, 19]. Therefore, the serial power transistor’s excess base current was the best measure of the circuit’s radia- tion response. After careful examination, the results from Table 1 may provide much information about the L4940V5 circuit’s radiation and post-irradiation response. All the irradiat- ed circuits expressed lower recovery (from deposition of the total dose of 500 Gy) during the ten-year room- temperature annealing than during the two seven-day high-temperature annealing sequences. Recovery of the circuits after two-week isothermal annealing was not complete, yet the main parameters pointed to cir- cuit damage comparable to the state recorded after the absorption of the total ionising dose of 50 Gy. Variations of the serial power transistor base current, presented in Table 1, may lead to the identification of two different circuit responses, for the irradiation and post-irradiation periods. The first category of re- sults comprises the initial period of irradiation (up to 50 or 200 Gy, depending on the bias and load condi- tions), as well as the final periods of high-temperature isothermal annealing. The second category of results comprises the data procured after absorption of higher total doses, as well as the initial annealing periods (par- ticularly the long-term, room-temperature annealing). The main means of identification of these categories is the saturation of the serial transistor’s base current, in either of the three data ensembles. The threshold value of the base current, when overcurrent protection is ac- tivated, is approximately 35 mA. This value corresponds to the total voltage regulator’s quiescent current of nearly 40 mA. When the serial transistor base current is always less than 35 mA, the radiation response of the PNP bipolar power transistor can be modelled with the standard Gummel–Poon model, with variations of only the maximum forward emitter current gain and the knee current. On the other hand, whenever the base current exceeded this threshold voltage, the SPICE model, successfully describing the circuit response for all three types of experiment, could not be made. In some cases, the power transistor base current was higher in control points with the collector current be- ing 100 mA, than in the case when the collector current was 400 mA! Figure 1: Waveforms of input and output voltage (left) and quiescent current (right), recorded on the unex- posed L4940V5 voltage regulator during the examina- tion of the maximum output current The bias conditions had a great influence on the radia- tion response of the irradiated circuits. Data from Table 1 show opposite trends of the radiation response of the power transistor, on the one hand, and the rest of the circuit, on the other. While the serial transistor’s base current increased, increasing also the voltage regula- tor’s quiescent current, the quiescent current of the control circuit (I Q0 ) declined [21]. Yet, the primary focus was on the examination of the characteristics of the vertical power transistor, since it had the most obvi- ous effect on the voltage regulator radiation response. So, analysing the variations of the excess base current, shown in Table 1, the clear scale of the radiation sen- sitivity of exposed circuits may be defined. Gamma- radiation inflicted the greatest damage on biased and heavily loaded voltage regulators (V in = 8 V, I = 500 mA). Lower degradation was seen in unbiased devices, fol- lowed by even lower degradation in biased and mod- erately loaded voltage regulators (V in = 8 V, I = 100 mA). The least damage was expressed by biased and negli- gibly loaded devices (V in = 8 V, I = 1 mA). The waveforms of the quiescent current and output current recorded on the laboratory setup are presented in Fig. 1. 5 Discussion 5.1 Computer simulation Fig. 2 presents a simplified computer simulation model of the L4940V5 voltage regulator, created in the pro- gram tool “LTspice IV” [33]. As can be seen from Fig. 2, the voltage reference and the error amplifier were rep- resented only by general models. On the other hand, V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 187 the simulation model of the serial PNP power transis- tor, Q12, was very complex. The main reason is the neg- ligible radiation degradation of the control circuit ele- ments, in opposition to the serious degradation of the serial power transistor. Due to its strong influence on the results obtained, the model included many details on the power supply circuit and the accompanying ca- bles. Due to the low value of the main filter capacitor (nomi- nally 330 μF), the examined voltage regulators oper- ated in two periods: with the constant output voltage and with its decreased value, falling below the nomi- nal value of 5 V (see Fig. 1). Therefore, the integrated circuit’s quiescent current had very rapid variations in these two operation sequences. Also, since the local ground of the examined voltage regulator was separat- ed from the power supply ground by a cable, 10 m long, it also increased the alternating current component of the voltage regulator’s quiescent current. In the period of 10 ms, matching the inherent frequency of the sin- gle-phase diode bridge, there was, de facto, operation of the voltage regulator with the dominant alternating current superimposed on its direct current component. Relatively low values of the maximum output current (being 720– 850 mA), as well as high values of the mini- mum dropout voltage, are a direct consequence of the low capacity of the main filter capacitor. Nevertheless, the experimental configuration was not changed, in order to enable mutual comparison of all the obtained and presented data, dating back to 2006 [17]. Yet, even in these circumstances, measurement of the mean val- ues of quiescent currents led to the correct calculation of the serial power transistor’s base current and its for- ward emitter current gain. Despite the high alternate current components, the computer simulation proved that the measured values of direct current, presented in tables 1 and 2, enabled successful evaluation of the voltage regulator’s radiation response. The reaction of the anti-saturation circuit was also im- portant, since it had a substantial influence on the qui- escent current response. Whenever the dropout volt- age on the pass PNP transistor fell below the threshold level, the anti-saturation circuit reacted in order to pre- vent the flow of excessive current from the serial tran- sistor to the substrate and, consequently, to the ground contact. Therefore, the anti-saturation circuit was mod- elled in great detail. Another important element was the overcurrent pro- tection of the driver NPN transistor, Q13. In order to prevent the voltage regulator’s quiescent current ris- ing above its upper limit of 50 mA [15], the transistor Q15 activates and takes the excessive collector current of the driver transistor, indirectly limiting the base cur- rent of the serial transistor. The consequence of this protection is the reduction of the voltage regulator’s maximum output current. This was exactly the circuit response that was recorded in numerous experiments, particularly after the absorption of the higher total dos- es of γ-radiation. As the basic element for modelling the serial vertical PNP power transistor, the SPICE model of discrete tran- sistor BC808-25 was used [36]. This is a discrete PNP transistor with the following nominal parameters: col- lector–emitter breakdown voltage BV CE0 = 25 V, nomi- nal collector current I C = 500 mA, cut-off frequency f T = 100 MHz, with the maximum value of the forward emit- Figure 2: Schematic circuit diagram of L4940V5 voltage regulator V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 188 ter current gain being in the range β F = 160–400 [37]. These data are close to the specified characteristics of the vertical PNP power transistor in device L4940V5 (f T = 80 MHz, β F = 50 for the load of 1 A, BV CE0 = 20 V) [15, 30]. Table 2 enables mutual comparison of simulation and experimental data on the serial transistor’s base cur- rent. Simulation data on parameters variations of the vertical serial PNP power transistor are also included in Table 1. Transistor parameters were selected in order to enable the highest possible agreement with the results for all three types of experiments. In the initial period of irradiation, for total ionising doses from 0 Gy up to 200 Gy, the simulation model reproduced the experi- mental results very well. In the initial phase, a sharp de- cline of the forward emitter current gain was seen for Table 2: Mutual comparison of absolute values of serial transistor’s base current (I B12 ) in voltage regulator STMicro- electronics ® L4940V5, obtained both with SPICE simulation and experiment. Experiments were executed on variations of dropout voltage (V EC12 ; for tests with load current of 100 mA and 400 mA) and maximum output current (I max ), for absorption of total ionising doses up to 500 Gy(SiO 2 ). The results were extended with parameters of the serial tran- sistor (maximum forward emitter current gain (β Fmax ) and knee current (I kF )), defined in the SPICE simulation models. Only experimental results that reached high agreement with simulation models were presented. Successive periods of isothermal annealing were marked as follows: annealing 2 (Θ a = 100°C, t = 168 hours); annealing 3 (Θ a = 150°C, t = 168 hours). STMicroelectronics® L4940V5 Simulation and experiment Simulation Operation during irradiation and annealing V CE12 (100 mA) V CE12 (400 mA) I max Parameters of serial PNP power transistor, Q 12 Bias and load during irradi- ation Dose, D [Gy] Simu- lation Experiment [20] Simulation Experiment [21] Simulation Experiment [18] β Fmax I kF [A] I B12 [mA] I B12 [mA] I B12 [mA] I B12 [mA] I B12 [mA] I B12 [mA] 0 V 0 A 0 0.72 0.55 4.67 4.63 20.77 20.4 270 0.225 50 1.18 1.32 7.72 8.39 27.77 29.38 115 0.375 Annealing 2 1.88 1.9 11.39 12.35 32.44 31.96 67 0.49 Annealing 3 1.1 1.18 7.06 6.45 21.57 26.1 125 0.38 8 V, 1 mA 0 0.89 0.7 4.03 3.82 19.06 19.03 340 0.225 50 1.08 1.09 5.17 5.16 21.53 20.73 180 0.375 100 1.36 1.49 7.33 7.41 27.73 27.3 115 0.425 200 2.5 2.53 12.39 14.89 34.39 33.97 45 1.1 Annealing 2 1.98 2.19 10.85 10.37 31.11 30.74 60 0.7 Annealing 3 0.94 1.06 5.8 5.43 20.67 21.6 150 0.39 8 V, 100 mA 0 0.89 0.73 4.03 4.42 19.06 18.07 340 0.225 50 1.09 1.38 7 7.1 26.32 24.89 127 0.375 100 2.14 2.21 11.51 12.01 33.87 31.15 55 0.75 Annealing 2 2.52 2.83 12.72 14.74 35.21 33.06 45 1 Annealing 3 1.13 1.25 7.14 6.78 24.22 23.97 120 0.4 8 V, 500 mA 0 0.79 0.73 5.7 5.64 23.23 25.3 240 0.2 50 1.35 1.41 8.86 8.97 30.62 29.45 100 0.375 Annealing 3 1.29 1.24 8.42 8.19 26.31 29.06 105 0.375 all the tested operation conditions [17-21]. This decline was successfully modelled in the computer simulation using just the variations of the maximum forward emit- ter current gain (β Fmax ) and the forward knee current (I kF ). Variations of the current gain and the excess base current were most successfully modelled for the biased and negligibly loaded voltage regulators. For other devices, both unbiased or biased and loaded with higher currents, procuring a faithful simulation model was much more difficult. Without exception, when the devices reached saturation of the excess base current, precise modelling was impossible. Unbiased and heav- ily loaded circuits L4940V5 entered this phase after the absorption of low total doses (50 Gy), while the biased and negligibly loaded devices experienced saturation after longer exposure (200 Gy). V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 189 Partially unexpected were data on the long-term room-temperature annealing. Initial checks of several irradiated samples led to the assumption that, in the long-term perspective, irradiated L4940V5 voltage reg- ulators would mostly recover [21]. Nevertheless, data obtained after 85,000 hours of room-temperature an- nealing did not support this hypothesis [34]. Despite the recovery of the serial transistor current gain and reduction of its excess base current, the maximum out- put current in most cases significantly declined. Yet, two successive one-week, high-temperature annealing sequences (100°C, followed by the 150°C exposure) led to the expressed circuit recovery. In all the examined cases, high-temperature annealing of devices irradi- ated until absorption of the total dose of 500 Gy led to nearly the same parameters as those recorded after absorption of 50–200 Gy. More important, these condi- tions could be again successfully modelled only with variations of the current gain and knee current of the serial transistor, just as in the initial period of irradia- tion. 5.2 Radiation effects As can be expected from the theory [38], unbiased de- vices suffer the most obvious damage, while bipolar intergated circuits with a high positive bias voltage dur- ing irradiation show much less degradation from the influence of radiation. On the one hand, this could be expected, since the high positive bias voltage injects the electrons in oxide, causing the trapped holes to recom- bine and consequently reducing the total oxide-trapped charge concentration. Yet, unbiased irradiation cannot enhance the hydrogen ions transport and, therefore, will have less influence on the build-up of interface traps. A sharp initial decline of the forward emitter current gain, presented in Table  1, points to the dominant influence of the oxide-trapped charge. The current gain declined rapidly, as presented in Table 1 and the maximum value of the forward emitter current gain decreased from 340 down to 55 (for biased and mod- erately loaded devices), following exposure to only 100 Gy. Also, at the same time the serial PNP power transistor’s knee current significantly increased, rising from 0.225 A to 0.75 A. The emitter-base leakage emis- sion coefficient, used in the simulation model of the transistor BC808-25 and, therefore, of the power verti- cal PNP transistor used in the present simulation, was a constant with a value n e = 1.568 [36]. Other voltage regulator elementary circuits were not seriously affect- ed by ionising radiation, so the remaining elements of the simulation model were not changed. This initial rapid degradation of the serial transistor cur- rent gain clearly points to the main negative influence of the oxide-trapped charge. Yet, in the previous re- search it was calculated that the emitter area has a sur- face doping concentration equal to 3.3·10 17   cm -3 [21]. This is a relatively high value for a PNP power transistor, and it was therefore assumed that the emitter should not be so much affected by the influence of the oxide- trapped charge, particularly since the emitter crowd- ing was not perceived [21]. Nevertheless, despite such a high impurities concentration for a power device, this value was not so high, particularly in comparison with a small-signal PNP transistor, having an emitter doping concentration up to 10 20  cm -3 [28]. Also, the interdigi- tated structure of the pass element, with 40 elemen- tary PNP power transistors [30], was another reason for its lower radiation tolerance. Therefore, the main rea- son for such an obvious rise in the excess base current was certainly primarily related with the emitter, rather than the base area. After the initial phase of radiation exposure, the next phase showed saturation in the serial PNP transistor’s excess base current, particularly after exposure of the samples to 500 Gy [18, 20, 21]. These results point to the reaction of the overcurrent protection of the NPN driver transistor Q13 (Fig. 2), preventing the rise of the voltage regulator’s quiescent current above the fore- seen maximum of 50 mA [15]. Saturation in the oxide- trapped charge build-up was always perceived for high total doses, being 500 Gy (with the exception of the biased and negligibly loaded samples). Yet, the prob- lem is that it was not possible to create an adequate computer simulation model of the PNP power transis- tor for higher total doses! Whatever was implemented in the SPICE model of the serial transistor, it was not possible to get mutually faithful results for either the maximum output current (I out = 720 – 850 mA) or the minimum dropout voltages (recorded for 100 mA and 400 mA) using the basic Gummel–Poon models. There were earlier attempts to simulate the increased recom- bination current in the base area, with the ideality fac- tor of 2 [8]. Other tools, such as additional resistors, cur- rent sources, variations of the surface recombination currents or the other power transistor parameters did not help much. The most successful attempt was made with the implementation of a significantly increased base-emitter saturation leakage current (I se ). Yet, even in these cases, it was not possible to alter one simple fact: regardless of the output current (100 mA, 400 mA or 800 mA), for a dose of 500 Gy, the base currents were, in most cases, nearly the same, being 35–40 mA. Nevertheless, even with this saturation of the base cur- rent, the experiment indicated that the voltage regula- tor operated correctly, without significant degradation of its output voltage and with only a moderate decline of the maximum output current at some control points. The exponential dependence of the base current on V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 190 the emitter-base voltage, accompanied by the success- ful simulation of the voltage regulator response with high output currents, could not be realised. So, despite the variations of either the emitter-base leakage cur- rent (I se ) or the emitter-base leakage emission coeffi- cient (n e ), a satisfactory simulation model suitable for the description of the high total-dose response could not be created. 5.3 Post-irradiation effects Data on the ten-year room-temperature annealing, presented in Table 1, point to a significant recovery of the serial transistor’s excess base current, hand in hand with further degradation of the maximum output cur- rent and, in some cases, minimum dropout voltage. More important, saturation of the excess base current remained present during the examination with higher currents, making it impossible to create faithful SPICE models of the first phase of annealing. Tremendous recovery of the excess base current may be observed particularly in unbiased devices, reducing the serial transistor’s base current nearly twentyfold! Also, in this, the most obvious case, the maximum output current, i.e. the serial transistor collector current, significantly declined. Various previous studies emphasize that, at room temperature, oxide-trapped charge anneals with time, contributing to the recovery of current gain [25], while interface traps in the field oxide often do not an- neal [39]. Thus, it may be assumed that, following the ten-year room temperature annealing of the L4940V5 voltage regulators, the oxide-trapped charge partially recovered, while the interface-trapped charge con- tinued to build up. Therefore, the power transistor’s current gain recovery was primarily affected by the positive influence of the recovery of the oxide-trapped Fig. 3. Variations of the power PNP transistor current gain as a function of the collector current in: a) unbiased circuits (V in = 0 V, V out = 0 A); b) biased and negligibly loaded (V in = 8 V, V out = 1 mA); c) biased and moderately loaded (V in = 8 V, V out = 100 mA); d) biased and heavily loaded circuits during irradiation (V in = 8 V, V out = 500 mA). Diagrams were created for constant collector–emitter voltage, being V CE = 3.3 V. Data were obtained from computer simulation models of the irradiated and annealed voltage regulators, which demonstrated high agreement with the experimental results presented in Table 1. V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 191 charge. The negative influence of further interface traps build-up, causing the serial transistor’s collector current to decline, had a much less obvious effect on its forward emitter current gain. The first high-temperature annealing sequence, includ- ing one-week at 100°C exposure, reduced the radiation damage to a level slightly above the one observed fol- lowing the 100-Gy irradiation. The second sequence, involving 168-hour annealing at 150°C, further reduced the radiation damage down to the degradation caused by the total ionising dose of 50 Gy. With the exception of the samples that were heavily loaded during the irra- diation, the voltage regulators’ characteristics, follow- ing the high-temperature annealing sequences, could be successfully modelled, in the same way it was done in the initial phase of irradiation, using the variations of only the current gain and knee current. No sign of heavy saturation was observed in the forward emitter current gain after exposure to higher total doses of γ-radiation. Data on the short-term, high-temperature annealing pointed to a substantial recovery of the irradiated cir- cuits, bringing them close to their pre-irradiation char- acteristics. Nevertheless, the data in Table 1 show that β Fmax recovered only to 40–50 % of their pre-irradiation values. Yet, even this was enough for a nearly complete recovery of the voltage regulator’s output parameters. Fig. 3 presents diagrams of the serial transistor’s forward emitter current gain variation as a function of its collec- tor current, in the range from 1 mA to 800 mA. For the specified collector currents, values of the serial transis- tor base-emitter voltage were in the range from 620 mV to 830 mV. Diagrams were produced from computer simulation models for all four types of bias and load conditions, briefly described in Table 1. The vertical PNP power transistor operates with output current being at least 1 mA, since this current flows through the voltage divider resistors when the voltage regulator operates without load. All data were obtained with a constant col- lector– emitter voltage of V CE = 3.3 V. Opposite to the re- sults presented in Table 1, based on the measured mean values, the data presented in Fig. 3 were obtained using the instantaneous values of voltages and currents, at the operation point with constant output voltage (V out = 5 V) and an appropriate input voltage of V in = 8.3 V. As can be seen from Table 1 and Fig. 3, the three iso- thermal annealing sequences led to similar character- istics of marginally irradiated and mostly recovered L4940V5 voltage regulators. The computer simulation models for these, principally different, periods, were basically the same. Yet, this could not be used as evi- dence that the distribution of the trapped charge was the same at the beginning and at the end of this decade-long experiment. Using only SPICE models, the influence of the interface traps and the oxide-trapped charge could not be separated. As already stated, the initial assumption of this research was that, as in the case of MOSFET-based logical circuits [29], most of the oxide-trapped charge would recover after 100°C an- nealing, while at the end of the 150°C annealing only the interface traps would remain. In discrete bipolar transistors, the interface states would recover first, after the annealing at 100°C–200°C, while the oxide-trapped charge would start to recover at higher temperatures, following the isothermal annealing at 150°C–300°C [14]. Taking into account the arguments presented in the previous chapters and paragraphs of this research, it seems that, indeed, the oxide-trapped charge in the tested circuits, at most, recovered after long-term room-temperature and short-term 100°C annealing. Nevertheless, there were no principal differences in the results obtained at the beginning of irradiation and at the end of the three annealing sequences, either in the model of the serial PNP power transistor or in the re- sponse of the entire L4940V5 voltage regulator. So, the results obtained may be used only for characterization of the total power transistor’s and voltage regulator’s radiation and post-irradiation response, rather than making it possible to qualitatively separate the effects of the interface traps and the oxide-trapped charge. 6 Conclusion Data on the more than decade long examinations of the radiation tolerance of L4940V5 voltage regulators were unified and extended with the newly procured isothermal annealing results. These COTS, automotive circuits, demonstrated unexpectedly high radiation hardness during the previous experiments, potentially qualifying them as a cheap replacement for specially designed rad-hard power integrated circuits. The same samples, exposed to the γ-radiation more than ten years ago, were further analysed after long-term, room- temperature annealing, followed by two sequences of short-term, high-temperature annealing. The circuit response gave a unique opportunity to analyse exclu- sively the radiation hardness of the vertical serial PNP power transistor, since the small-signal, control circuit was marginally affected by ionising radiation. A broad ensemble of the experimental data enabled the creation of a credible SPICE model, successfully describing the circuit response in the γ-radiation field. The initial phase of irradiation, up to 200 Gy, was effi- ciently recreated using the variations of the maximum forward emitter current gain and the knee current of the serial PNP power transistor. The data and computer simulation showed significant agreement for load cur- V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 192 rents of 100 mA, 400 mA and nearly 800 mA, for various input voltages. The subsequent exposure to γ-radiation could not be successfully modelled, due to the ex- pressed saturation of the serial transistor’s excess base current. The current limit protection of the driver NPN transistor further affected the circuit response. Ten-year room-temperature annealing of integrated circuits, irradiated up to 500 Gy, caused the great re- covery of the voltage regulator’s quiescent current, yet followed by the further degradation of the maximum output current. The primary reason for the described response was the mutual recovery of the oxide-trapped charge and the build-up of interface traps above the emitter area of the serial PNP power transistor. On the other hand, two successive, one-week, high-tempera- ture annealing periods caused the tremendous recov- ery of all the irradiated voltage regulators, reducing the circuit degradation down to the level specified after absorption of the total dose of 50 Gy. The initial phase of irradiation caused the voltage regu- lator to degrade primarily through the influence of the oxide-trapped charge. The second phase of irradiation is a consequence of the activation of the overcurrent protection of the NPN driver transistor, followed by the saturation of the trapped charge density. Despite the relatively high doping concentration of the P-type emitter area in the vertical PNP power transistor, in- creased surface recombination in the area of the inter- digitated emitter was the primary cause of the sharp increase in the serial transistor’s excess base current. Saturation of the serial transistor’s excess base current after long-term, room-temperature annealing prevent- ed the efficient modelling of this post-irradiation re- sponse. On the other hand, in most cases the response to the high-temperature annealing could be faithfully modelled in the same manner as during the initial phase of the voltage regulator irradiation. 7 Acknowledgement This work was supported by the Ministry of Education, Science and Technological Development of the Repub- lic of Serbia under the project 171007, “Physical and functional effects of the interaction of radiation with electrical and biological systems” . 8 References 1. G. A. Rincon-Mora, Analog IC design with low- dropout regulators, McGrawHill Education (2014). 2. R.L. Pease, Total ionizing dose effects in bipolar devices and circuits, IEEE T Nucl Sci 50 (2003) 539- 551. 3. D. M. Fleetwood, Total ionizing dose effects in MOS and low-dose-rate-sensitive linear-bipolar devices, IEEE T Nucl Sci 60 (2013) 1706-1730. 4. V. S. Pershenkov, V. B. Maslov, S. V. Cherepko, I. N. Shvetzov-Shilovsky, V. V. Belyakov, A. V. sogoyan, V. . Rusanovsky, V. N. Ulimov, V. V. Emelyanov, V. S. Nasibullin, The effect of emitter junction bias on the low dose-rate radiation response of bipolar devices, IEEE T Nucl Sci 44 (1997) 1840–1848. 5. J. Assaf, Bulk and surface damages in comple- mentary bipolar junction transistors produced by high dose irradiation, Chin Phys B 27 (2018) 016103 1-8. 6. F. J. Franco, C. Palomar, J. G. Izquierdo, J. A. Agap- ito, SPICE simulations of single event transients in bipolar analog integrated circuits using public information and free opeen source tools, IEEE T Nucl Sci 62 (2015) 1625-1633. 7. M. R. Shaneyfelt, J. R. Schwank, D. M. Fleetwood, R. L. Pease, J. A. Felix, P . E. Dodd, M. C. Maher, An- nealing behaviour of linear bipolar devices with enhanced low-dose-rate sensitivity, IEEE T Nucl Sci 51 (2004) 3172-3177. 8. J. Beaucour, T. Carribre, A. Gach, P. Poirot, Total dose effects on negative voltage regulator. IEEE T Nucl Sci 41 (1994) 2420-2426. 9. P . C. Adell, R. D. Schrimpf, W. T. Holman, J. L. Todd, S. Caveriviere, R. R. Cizmarik, K. F. Galloway, Total dose effects in a linear voltage regulator, IEEE T Nucl Sci 51 (2004) 3816-3821. 10. V. Ramachandran, B. Narasimham, D. M. Fleet- wood, R. D. Schrimpf, W. T. Holman, A. F . Witulski, R. L. Pease, G. W. Dunham, J. E. Seiler, D. G. Platteter, Modeling total-dose effects for a low-dropout voltage regulator, IEEE T Nucl Sci 53 (2006) 3223- 3231. 11. R. L. Pease, S. McClure, J. Gorelick, S. C. Witczak, Enhanced low-dose-rate sensitivity of a low- dropout voltage regulator, IEEE T Nucl Sci 45 (1998) 2571-2576. 12. E. W. Enlow, R. L. Pease, W. E. Combs, R. D. Schrimpf, R. N. Nowlin, Response of advanced bipolar pro- cesses to ionizing radiation, IEEE T Nucl Sci 38 (1991) 1342-1349. 13. R. L. Pease, ELDRS in bipolar linear circuits: a re- view, IEEE T Nucl Sci 56 (2009) 1894-1908. 14. A. Holmes-Siedle, L. Adams, Handbook of Radia- tion Effects, Oxford University Press (2004). 15. L4940 Series - very low dropout 1.5A regulators, STMicroelectronics (2003). 16. F. Bertotti, C. Cini, C. Contiero, P. Galbiati, Mono- lithically integrated semiconductor device con- taining bipolar junction transistors, CMOS and V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193 193 DMOS transistors and low leakage diodes and a method for its fabrication, United States Patent 4887142, Dec. 12 (1989). 17. V. Vukić, P. Osmokrović, Total ionizing dose re- sponse of commercial process for synthesis of lin- ear bipolar integrated circuits, J Optoel Adv Mater 8 (2006) 1538-1544. 18. V. Vukić, P . Osmokrović, Impact of forward emitter current gain and geometry of PNP power transis- tors on radiation tolerance of voltage regulators, Nucl Technol Radiat 25 (2010) 179-185. 19. V. Dj. Vukić, P . V. Osmokrović, On-line monitoring of base current and forward emitter current gain of voltage regulator’s serial PNP transistor in radi- ation environment, Nucl Technol Radiat 27 (2012) 152-164. 20. V. Dj. Vukić, P. V. Osmokrović, Gamma-radiation response of isolated collector vertical PNP power transistor in moderately loaded voltage regula- tor L4940V5, J Optoel Adv Mater 15 (2013) 1075- 1083. 21. V. Dj. Vukić, P . V. Osmokrović, Impact of the excess base current and the emitter injection efficiency on radiation tolerance of a vertical PNP power transistor in a voltage regulator, Inf MIDEM 43 (2013) 27-40. 22. G. C. Messenger, M. S. Ash, The Effects of Radia- tion on Electronic Systems, Van Nostrand Rein- hold (1992). 23. D. M. Schmidt, D. M. Fleetwood, R. D. Schrimpf, R. L. Pease, R. J. Graves, G. H. Johnson, K. E. Galloway, W. E. Combs, Comparison of ionizing-radiation-in- duced gain degradation in lateral, substrate and vertical PNP BJTs, IEEE T Nucl Sci 42 (1995) 1541- 1549. 24. Star-HSPICE Manual, Avant! Corporation (1998). 25. D. M. Schmidt, A. Wu, R. D. Schrimpf, D. M. Fleet- wood, R. L. Pease, Modeling ionizing radiation in- duced gain degradation of the lateral PNP bipolar junction transistor, IEEE T Nucl Sci 43 (1996) 3032- 3039. 26. H. J. Barnaby, B. Vermeire, M. J. Campola, Improved model for inncreased surface recombination cur- rent in irradiated bipolar junction transistors, IEEE T Nucl Sci 62 (2015) 1658-1664. 27. X. Li, J. Yang, H. J. Barnaby, K. F. Galloway, R. D. Schrimpf, D. M. Fleetwood, C. Liu, Dependence of ideality factor in lateral PNP transistors on surface carrier concentration, IEEE T Nucl Sci 64 (2017) 1549-1553. 28. A. Wu, R. D. Schrimpf, H. J. Barnaby, D. M. Fleet- wood, R. L. Pease, S. L. Kosier, Radiation-Induced Gain Degradation in Lateral PNP BJTs with Lightly and Heavily Doped Emitters, IEEE T Nucl Sci 44 (1997) 1914-1921. 29. C. E. Barnes, D. M. Fleetwood, D. C. Shaw, P . S. Wi- nokur, Post irradiation effects (PIE) in integrated circuits, IEEE T Nucl Sci 39 (1992) 328-341. 30. R. Gariboldi, M. Morelli, Very-low-drop voltage regulator with a fully complementary power pro- cess, IEEE J Solid-St Circ 22 (1987) 447–450. 31. A. Andreini, C. Contiero, P. Galbiaty, A new inte- grated silicon gate echnology combining bipolar linear, CMOS logic, and DMOS power parts, IEEE T Electr Dev 33 (1986) 2025-2030. 32. F. Bertotti, P. Ferrari, M. T. Gatti, Saturation limit- ing system for a vertical, isolated collector PNP transistor and monolithically integrated structure thereoff, United States Patent 4887141, Dec. 12 (1989). 33. LTSpice-Version 4.13q, Linear Technology Corpo- ration (2012). 34. V. Dj. Vukić, Rapid and long-term gamma-radia- tion annealing in low-dropout voltage regulators, Nucl Technol Radiat 32 (2017) 155-165. 35. V. Dj. Vukić, P . V. Osmokrović, Failure of the nega- tive voltage regulator in medium-photon-energy X radiation field, Microelectron Reliab 54 (2014) 79-89. 36. Standard.BJT, LT Wiki, Linear Technology Corpora- tion (2012) http://ltwiki.org/?title=standard.bjt 37. BC808-25LT1G, General Purpose Transistors, On- Semiconductor (2016). 38. A. H. Johnston, B. G. Rax, Testing and qualifying linear integrated circuits for radiation degrada- tion in space, IEEE T Nucl Sci 53 (2006) 1779-1786. 39. A. Johnston, R. Swimm, R. D. Harris, D. Thorbourn, Dose rate effects in linear bipolar transistors, IEEE T Nucl Sci 58 (2011) 2816-2823. Arrived: 14. 04. 2018 Accepted: 30. 07. 2018 V. Dj. Vukić; Informacije Midem, Vol. 48, No. 3(2018), 181 – 193