L. KALINA et al.: THICKNESS DETERMINATION OF CORROSION LAYERS ON Fe USING XPS DEPTH PROFILING 537–540 THICKNESS DETERMINATION OF CORROSION LAYERS ON IRON USING XPS DEPTH PROFILING DOLO^EVANJE DEBELINE KOROZIJSKIH PLASTI NA @ELEZU Z UPORABO XPS GLOBINSKEGA PROFILIRANJA Luká{ Kalina, Vlastimil Bílek Jr., Marek Bu{o, Jan Koplík, Jiøí Másilko Brno University of Technology, Faculty of Chemistry, Materials Research Centre, Purkyòova 118, 612 00 Brno, Czech Republic kalina@fch.vutbr.cz Prejem rokopisa – received: 2016-07-15; sprejem za objavo – accepted for publication: 2018-03-08 doi:10.17222/mit.2016.180 The study deals with the methodology and thickness determination of the corrosion layers of ferritic steel samples using X-ray photoelectron spectroscopy (XPS) equipped with the ion-gun source system enabling destructive depth profiling. It is well known that XPS is one of the most often used techniques for determining both the thickness and chemical composition of passive films or corrosive layers. Unfortunately, the thickness of ion-gun-etched layers can only be estimated for simple samples and standards. Corrosion layers are heterogeneous and vary in composition; therefore, the etching rate is specific for each corrosion layer. The results of this work provide the possibility for a fast and easy determination of the ion-gun sputtering effect with exact settings for multi-compound chemical structures. The knowledge related to the thickness of corrosion or passivation layers would help greatly in their characterization. Keywords: X-ray photo-electron spectroscopy, ion gun, depth profiling, corrosion layer [tudija opisuje metodologijo in dolo~evanje debeline korozijskih plasti na vzorcih feritnega jekla z uporabo rentgenske foto- elektronske spektroskopije (XPS; angl.: X-ray Photoelectron Spectroscopy). Uporabljena naprava je bila opremljena z ionsko pu{ko, ki omogo~a destruktivno globinsko profiliranje. Znano je, da je XPS ena od najbolj uporabljanih tehnik za dolo~evanje tako debeline kot tudi kemijske sestave pasivacijskih filmov ali korozijskih plasti. @al se debelina plasti, jedkane z ionsko pu{ko, lahko oceni samo na enostavnih vzorcih in standardih. Korozijske plasti so heterogene in imajo spremenljivo kemijsko sestavo, zato je hitrost jedkanja specifi~na za vsako korozijsko plast posebej. Rezultati tega dela zagotavljajo mo`nost hitrega in enostavnega dolo~evanja u~inkov jedkanja z ionsko pu{ko z natan~nimi nastavitvami za ve~komponentne kemijske strukture. Znanje, pridobljeno v okviru tega dela, bo lahko v precej{njo pomo~ pri karakterizaciji debeline korozijskih ali pasivacijskih plasti. Klju~ne besede: rentgenska fotoelektronska spektroskopija, ionska pu{ka, globinsko profiliranje, korozijska plast 1 INTRODUCTION X-ray photoelectron spectroscopy (XPS), often re- ferred to as electron spectroscopy for chemical analysis (ESCA), is a surface analytical technique that has ma- tured into an essential tool for the characterization of many materials. The ability to obtain the information on the surface-element composition as well as on the chemi- cal state and electronic state of the elements that exist within a material is one of its advantages. XPS of course owes its quantification to Einstein’s explanation of photoelectric effect in 1905. 1 In the period since the late 1950s, the photoelectric effect has been de- veloped into one of the most powerful tools for the study of the composition of the matter. 2 Kai Siegbahn took the advantage of this fact for the development of high-reso- lution XPS, for which he received the Nobel Prize in 1981. Modern XPS spectrometers depend largely upon monochromated Al X-rays as a primary excitation source to eject a photoelectron from an atom at the sample’s surface (from the top 1 nm to 10 nm). 3 Photoelectrons emitted from a sample are separated on the basis of their kinetic energy and analyzed in an XPS detector by mea- suring the kinetic energy of electrons which provides the information needed for determining the elements present in the sample. In a research of thin corrosion or passivation layers, it becomes necessary to know the chemical composition of these layers as well as their thickness. 4 Especially the knowledge about the oxidation or corrosion behavior of iron provides important information related to the utili- zation of protective passive films on its surface or the magnetic properties. Therefore, the understanding of the corrosion processes of iron is important when choosing the material for a certain purpose. The composition of the corrosion layers is most reliably determined with X-ray diffraction. However, in many cases the oxide film is too thin for this technique to be applied and the identi- fication of the phases requires sensitive surface chemical methods. For this purpose, the routine part of analyzing the surface and thin film for compositional depth profil- ing is the use of a combination of XPS and ion-gun etch- ing. The ion beam is obtained due to the collision be- tween gas and electrons; the solid surface is then bombarded with energetic argon ions to successively re- move the outermost layers and the underlying layers be- come a new surface. This process reveals a new layer, Materiali in tehnologije / Materials and technology 52 (2018) 5, 537–540 537 UDK 543.428.3:669.1:620.19 ISSN 1580-2949 Original scientific article/Izvirni znanstveni ~lanek MTAEC9, 52(5)537(2018) which is then characterized with XPS (Figure 1). It would be also very useful to determine the sputter effect of the ion gun to find the depth of etching at a specific voltage and the spot size for chemical compounds or more complex systems. In this paper, a detailed XPS analysis of the corrosion layers on steel samples and the methodology for determining their thickness are pre- sented. 2 EXPERIMENTAL PART 2.1 Materials and sample preparation Ferritic steel was used as the base material for the test samples. The steel was cut to the required dimensions of (10 × 15 × 1) mm using a Struers Secoton-50 saw. Small specimens were grinded and polished and then exposed to the corrosion environment in a furnace under normal atmospheric pressure, with various exposure times and temperature conditions (100, 200, 250 and 600) °C. The samples were then immediately loaded into the XPS sys- tem with an ultra-high vacuum. 2.2 Ion-gun etching The depth profile was acquired by Ar + etching. The ion gun was under full computer control allowing the standard settings to be recorded and recalled for future experiments. The standard operating conditions for the depth profile were a beam energy of 4 keV and a sputter current of 2.6 μA. The ion beam was scanned in a square raster (4 mm 2 ) over the specimen surface. The size of the raster was approximately 10 times larger than the XPS-measured area. Rastering the ion beam in this way ensures that the XPS spectra are representative in the middle of the square etch pit and not at the edge where the ion beam may have caused uneven etching (šedge’ ef- fects). 2.3 X-ray photoelectron spectroscopy (XPS) XPS analyses were carried out with an Axis Ultra DLD spectrometer using a monochromatic Al K (h = 1486.7 eV) X-ray source operating at 150 W (10 mA, 15 kV). The spectra were obtained using an analysis area of ~300 × 700 μm. The Kratos charge neu- tralizer system was used for all the analyses. High-reso- lution spectra were measured with a step size of 0.1 eV and pass energy of 20 eV. The instrument base pressure during the measurements was consistently 2·10 –8 Pa. The spectra were analyzed using the CasaXPS software (ver- sion 2.3.15) and were charge-corrected to the main line of the C 1s spectral component (C–C, C–H) set to 284.80 eV. The standard Shirley background was used for all the sample spectra. 3 RESULTS AND DISCUSSION Four various temperatures were chosen for the study of the corrosion rate at different exposure times. At the temperatures ranging from 150 °C to 600 °C, ferritic steel reacts chemically with oxygen from the air/aerial oxygen to form a surface film with various kinds of iron oxides. This type of corrosion involves a high-tempera- ture oxidation reaction, which occurs in the dry state. The formation of iron oxides on steel samples usually follows a logarithmic rate, which can be observed in Fig- ure 2. The character of the corrosion layer depends mainly on the applied temperature. It can be expected that samples heated at a temperature below 600 °C will be covered with Fe 3 O 4 and Fe 2 O 3 and above this temper- ature, samples oxidize to form FeO, Fe 3 O 4 and Fe 2 O 3 . Similar results were also obtained during the XPS depth profiling (Figure 3) of the sample exposed to the tem- perature of 600 °C for 24 h. The investigation of the XPS spectra was carried out theoretically. The Gupta and Sen (GS) peak parameters relate to the multiplet splitting of unpaired photoelectrons in the valence band and arise from different spin distributions of electrons of the band structure. 5–6 The Fe 2p 3/2 envelopes from high-spin Fe 3+ compounds follow the GS predictions very well even when the system contains different iron oxides and be- comes complicated due to spectral overlaps. Based on these fitting parameters, it was determined that the sur- L. KALINA et al.: THICKNESS DETERMINATION OF CORROSION LAYERS ON IRON USING XPS DEPTH PROFILING 538 Materiali in tehnologije / Materials and technology 52 (2018) 5, 537–540 Figure 1: Process of XPS depth profiling Figure 2: Dependence of the ion-etching time on different high-tem- perature corrosion exposures face of the sample was formed by -Fe 2 O 3 with a very thin -FeOOH phase (Figure 3A). After the etching away of several nanometers, another corrosion product appeared (Figure 3B). This spectrum is distinct from the previous one, with a shoulder on the low binding energy side that is specific to the presence of the Fe 2+ multiplet component in the FeO·Fe 2 O 3 phase. The extension and the shift of the shake-up satellite peak, related to the in- teraction of the outgoing photoelectron with a valence electron, is also an additional effect pertaining to the Fe 2+ portion. Finally, after 510 s of ion etching (Figure 3C), an asymmetric peak of iron was detected. With respect to the roughness of the sample, ion etching was stopped when the amount of Fe 0 was equal to that of iron oxides. The determination of the thickness of a corrosion layer is dependent on the sputter yield of each phase present in the system. This physical constant describes the rate, at which the material is removed from the sam- ple during the bombardment by energetic ions. The sput- ter yield (Y) is derived from the density and energy of sublimation of the specific chemical compound. 7 Subse- quently, after substituting it into the equation, the etch rate R is defined: 8 R IYw A = − 10 2 (nm s –1 ) (1) where I = ion-beam current (μA), w = molar weight (g mol –1 ), = density (g cm –3 ) and A = raster area (mm 2 ). The depth of the etched layer in the specific time of ion sputtering is related to the proportions of indivi- dual phases; therefore, the XPS quantification analysis becomes an inseparable part of depth profiling. If the percent proportion of a particular phase is related to coefficient k, the etch rate R and the time of etching t, then the etched multi-compound layer thickness T is given by: TkRkRkRt nn =⋅+⋅+⋅ () 1122 (nm) (2) Thanks to the sequential ion etching and depth profile analysis, the character of the corrosion layer is shown in Figure 4. 4 CONCLUSIONS This paper demonstrates a fast and easy method for the characterization of the corrosion layer on steel sam- ples. Through both the sequential destructive method of ion etching and a detailed XPS analysis, it is possible to identify the exact amount of each corrosive product at a given depth. Based on the chemical composition and ion-gun setting, the degree and speed of ion etching were calculated. Based on the amount of each corrosion prod- L. KALINA et al.: THICKNESS DETERMINATION OF CORROSION LAYERS ON IRON USING XPS DEPTH PROFILING Materiali in tehnologije / Materials and technology 52 (2018) 5, 537–540 539 Figure 4: Character of the corrosion layer of the sample heated at 600 °C for 24 h Figure 3: Corrosion-product components at various depths for the sample heated at 600 °C for 24 h uct and its etch rate, the character of the corrosion layer in a specific corrosion environment was derived. Acknowledgement This outcome was achieved with the financial support for the project: Materials Research Centre at FCH BUT – Sustainability and Development, REG LO1211, the fi- nancial support from the National Programme for Sustainability I (Ministry of Education, Youth and Sports). 5 REFERENCES 1 A. Einstein, Concerning an heuristic point of view towards the emission and transformation of light, Annalen der Physik, 17 (1905), 132–148 2 C. S. Fadley, X-ray photoelectron spectroscopy: Progress and per- spectives, Journal of Electron Spectroscopy and Related Phenomena, 41 (2010), 178–179, doi:10.1016/j.elspec.2010.01.006 3 O. Renault, High-resolution XPS spectromicroscopy, Surface and Interface Analysis, 42 (2010), 816–825, doi:10.1002/sia.3521 4 R. Steinberger, J. Walter, T. Greunz, J. Duchoslav, M. Arndt, S. Molodtsov, D. C. Meyer, D. Stifter, XPS study of the effects of long-term Ar + ion and Ar cluster sputtering on the chemical degradation of hydrozincite and iron oxide, Corrosion Science, 99 (2015), 66–75, doi:10.1016/j.corsci.2015.06.019 5 R. P. Gupta, S. K. Sen, Calculation of multiplet structure of core p-vacancy levels, Physical Review B, 10 (1974), 71–77, doi:10.1103/PhysRevB.10.71 6 R. P. Gupta, S. K. Sen, Calculation of multiplet structure of core p-vacancy levels II, Physical Review B, 12 (1975), 15–19, doi:10.1103/PhysRevB.12.15 7 M. P. Seah, T. S. Nunney, Sputtering yields of compounds using argon ions, Journal of Physics D, 43 (2010), 1–13, doi:10.1088/ 0022-3727/43/25/253001 8 J. F. Watts, J. Wolstenholme, An introduction to surface analysis by XPS and AES, 2 nd ed., Wiley, Chichester 2003, 226 L. KALINA et al.: THICKNESS DETERMINATION OF CORROSION LAYERS ON IRON USING XPS DEPTH PROFILING 540 Materiali in tehnologije / Materials and technology 52 (2018) 5, 537–540